Bulgarian 'PULSE STAR' (... close to Legendary one)

[kt315]

我已经做好了脉冲星，但识别并不是非常好,电路中有非常多要改动的地方，我可以给大家一些解答

your chinese hieroglyphic is PERFFECT! to my sorry it is unreadable (((

[fengzhai01]

我已经做好了脉冲星，但识别并不是非常好,电路中有非常多要改动的地方，我可以给大家一些解答

[mohandes]

for Georgi

hi Georgi
now i want complete this. just tell me this pcb is ok , or no .
regards
or any one can help me

http://p30up.ir/images/ryvil2xg5sy0pd38pe0.rar

[mohandes]

This is normal . mohandes , this shematic is no for you , You do not have forces to do Puls Star -g . PLEASE STOP PROJECT PS .

OK man
i design again the third board like your schematic and get find,all TP point are ok and set.

just LEVEL meter not work(very very bad) and about the discrimination i should test it tomorrow

and both Led(red and green )always on and off!!!!!!

my coil is 500mkh and 2ohm ,R parallel is 220ohm.

all waves like # 515
thanks man

[georgi.g.zhelev]

hi georgi
just tell me why when i return Delay pot(U2-pin6)all TP points changes ????please
i set tp and then when i return it all TP go fault

This is normal . mohandes , this shematic is no for you , You do not have forces to do Puls Star -g . PLEASE STOP PROJECT PS .

[mohandes]

hi georgi
just tell me why when i return Delay pot(U2-pin6)all TP points changes ????please
i set tp and then when i return it all TP go fault

[mohandes]

[QUOTE=mohandes;177971]

Yes i read it and all is ok( i print it and save all figures in my mind ).please see #535 and#543.
when i connect to third board (TP points my means )i can just adjust one of the them and it is TP5(adjust by Delay or Rv3 and Rv9) to 0.6volts.
but Tp3 dont fall down to-2.9volts , so can i change the Rv7 to 20Kohm pot??????????
explain more : when i change Rv6 or PPS or FCY can be adjust it but pin6 ne5534 not in -0.2volts , so what am i do?

best sens for delay on 50mks or 100mks?
and 450volt is ok ?

[mohandes]

[QUOTE=georgi.g.zhelev;177962]

hi
i need the waves of X,Y,Z of 4053 ,please

mr georgi my coil can be 450volt p-p ,is it ok?for biger voltages i should reduce the coil Inductance or increase R parallel to the coil???[/QUOT

mohandes,Did you read what I write you? SEE # 515!!

Yes i read it and all is ok( i print it and save all figures in my mind ).please see #535 and#543.
when i connect to third board (TP points my means )i can just adjust one of the them and it is TP5(adjust by Delay or Rv3 and Rv9) to 0.6volts.
but Tp3 dont fall down to-2.9volts , so can i change the Rv7 to 20Kohm pot??????????
explain more : when i change Rv6 or PPS or FCY can be adjust it but pin6 ne5534 not in -0.2volts , so what am i do?

best sens for delay on 50mks or 100mks?
and 450volt is ok ?

[georgi.g.zhelev]

[QUOTE=mohandes;177952]hi
i need the waves of X,Y,Z of 4053 ,please

mr georgi my coil can be 450volt p-p ,is it ok?for biger voltages i should reduce the coil Inductance or increase R parallel to the coil???[/QUOT

mohandes,Did you read what I write you? SEE # 515!!

[kt315]

for more voltage amplitude you have to encrease PULSE WIDTH. also you need to change your mos-fet IRF740 on another transistor type. because max peak voltage for IRF740 is only 400V. you have reached the limit with 450V and will NOT get MORE.

[mohandes]

hi
i need the waves of X,Y,Z of 4053 ,please

mr georgi my coil can be 450volt p-p ,is it ok?for biger voltages i should reduce the coil Inductance or increase R parallel to the coil???

[mohandes]

hi georgi
just tell me my X,Y,Z out put have correct waves?

X :

Y:

Z:

[mohandes]

ok
today i try to fix TP points but i just can set TP5 on 0.6v
thanks

[georgi.g.zhelev]

corect

[georgi.g.zhelev]

mohandes , your PCB is many bad design . SEE CORRECT PCB!