Bulgarian 'PULSE STAR' (... close to Legendary one)

[georgi.g.zhelev]

THanks george
I go to another city in my country to buy the part list limit 1500km@!!!!!!!!
My design pcb in ALEXSES schematic in after week.
you say the resistor rang can between 65...75k and 1%:that means between 65...75k 1W.alright?
I turn the old coil around autoclave that was my old detector.
can I turn coil of the ps-g separate.then when I turn both of them I connect them together.Is that right?
SEE FOTO front panel PULS STAR -G .that is ALEXSIS FOTO means or your?
regards

Аll RESISTORS ... 0,25w оr 0,125w !!!! only R6= 240...330ohm (parallel to the coil ) ...2w !!!

[mohandes]

THanks george
I go to another city in my country to buy the part list limit 1500km@!!!!!!!!
My design pcb in ALEXSES schematic in after week.
you say the resistor rang can between 65...75k and 1%:that means between 65...75k 1W.alright?
I turn the old coil around autoclave that was my old detector.
can I turn coil of the ps-g separate.then when I turn both of them I connect them together.Is that right?
SEE FOTO front panel PULS STAR -G .that is ALEXSIS FOTO means or your?
regards

[georgi.g.zhelev]

HI georgi
thganks for answer.any way aH have many ? for you.
1-it is ok in http://ups.night-skin.com/up-91-10/need2.jpg x y z or pin 14 15 4 sequence Connecte to pin 2 u6,pin 6 u2, pin 2 u10?
2-and http://axgig.com/images/34942843928840265332.jpg
3- for the source can i use two 9 volt battery book?
thanks.

# only DALAY is potenciometer(SEE FOTO front panel PULS STAR -G ), microampermeter ..250mkrA, zero in the middle >0<. All capacitors, polyester, high quality (WIMA). 2X 9 V blok... NO. blok AKU 12pcs x 1,2v ...1,500....3,000 mAh.

[mohandes]

hello jab
i will Electrical Power Engineering one years later.
all of you sorry me.
yes you say ok for me.but i have a Interest

[jap]

so sorry george.
thanks.
sorry i am going to Engineering electrical.

Hi mohandes
###### It is not for beginners#####
-All u ask question does not need,What do you do in the project and you learn about the components,after work of the project is clear you are going to ask!!!!
- what you ask for does not need Faculty of electrical Engineering ,that the principles of electrical components.

-----I advise you first start with pcb of picture 4 in reply#423 and get all voltages exactly because it is the key to the success of the project.
-And when you ask in the project after its implementation will answerd.
*****Thank you georgi.g.zhelev
--- and on the tender and on answering and along the patience
best time
j.

[mohandes]

HI georgi
thganks for answer.any way aH have many ? for you.
1-it is ok in http://ups.night-skin.com/up-91-10/need2.jpg x y z or pin 14 15 4 sequence Connecte to pin 2 u6,pin 6 u2, pin 2 u10?
2-and http://axgig.com/images/34942843928840265332.jpg
3- for the source can i use two 9 volt battery book?
thanks.

[georgi.g.zhelev]

[QUOTE=mohandes;165680]so sorry george.
ok I just dont know whichi is multi turn and volume.because i wanna set the part list.
thanks.

VOLUME ....multi turn ?????? Why multiturn potentiometer ? VOLUME >no multi turn potenciometer !!

[mohandes]

so sorry george.
ok I just dont know whichi is multi turn and volume.because i wanna set the part list.
thanks.
sorry i am going to Engineering electrical.
realy very thank you,i am not stupid but i have very sensivity

[georgi.g.zhelev]

thanks george & hi

http://ups.night-skin.com/up-91-10/need.jpg

http://ups.night-skin.com/up-91-10/need2.jpg

http://ups.night-skin.com/up-91-10/need3.jpg

http://ups.night-skin.com/up-91-10/need4.jpg

http://ups.night-skin.com/up-91-10/multi-turn-volume.jpg

again my qustion in my pictures.
regards & thanks.

Hi, mohandes! Please stop, many stupid questions, this scheme is not for you,SORRY!!

[georgi.g.zhelev]

Hello george

Originally Posted by mohandes
hello georgi.g.zhelev
sorry me please? is shematic is right and now I am making that.but have a few question?
http://ups.night-skin.com/up-91-10/help-.jpg
http://ups.night-skin.com/up-91-10/help2.jpg
http://ups.night-skin.com/up-91-10/help1.jpg

my question are in my picture



# 1.......300mikr.H ..... choke (ferrite)
#2 ......COIL > 0,8.....1,2ohm, 400...500mikr.H; diametr....30cm.
#3........300mikr.H ..... choke (ferrite)

http://ups.night-skin.com/up-91-10/choke.jpg

again my ? in the picture
regards

#1 >100....300mkr.H

[mohandes]

Hello george

Originally Posted by mohandes
hello georgi.g.zhelev
sorry me please? is shematic is right and now I am making that.but have a few question?
http://ups.night-skin.com/up-91-10/help-.jpg
http://ups.night-skin.com/up-91-10/help2.jpg
http://ups.night-skin.com/up-91-10/help1.jpg

my question are in my picture



# 1.......300mikr.H ..... choke (ferrite)
#2 ......COIL > 0,8.....1,2ohm, 400...500mikr.H; diametr....30cm.
#3........300mikr.H ..... choke (ferrite)

http://ups.night-skin.com/up-91-10/choke.jpg

again my ? in the picture
regards

[mohandes]

thanks george & hi

http://ups.night-skin.com/up-91-10/need.jpg

http://ups.night-skin.com/up-91-10/need2.jpg

http://ups.night-skin.com/up-91-10/need3.jpg

http://ups.night-skin.com/up-91-10/need4.jpg

http://ups.night-skin.com/up-91-10/multi-turn-volume.jpg

again my qustion in my pictures.
regards & thanks.

[scs]

This scheme works as normal PI detector.Work with great strobe delay . Reacts better iron . Very poor silver discrimination . PI detectors with one coil have poor discrimination.Slow motion or non motion detector with meter discriminator work better.

[georgi.g.zhelev]

hello georgi.g.zhelev
sorry me please? is shematic is right and now I am making that.but have a few question?

http://ups.night-skin.com/up-91-10/help-.jpg

http://ups.night-skin.com/up-91-10/help2.jpg

http://ups.night-skin.com/up-91-10/help1.jpg

my question are in my picture

# 1.......300mikr.H ..... choke (ferrite)
#2 ......COIL > 0,8.....1,2ohm, 400...500mikr.H; diametr....30cm.
#3........300mikr.H ..... choke (ferrite)

[mohandes]

hello georgi.g.zhelev
sorry me please? is shematic is right and now I am making that.but have a few question?

http://ups.night-skin.com/up-91-10/help-.jpg

http://ups.night-skin.com/up-91-10/help2.jpg

http://ups.night-skin.com/up-91-10/help1.jpg

my question are in my picture