raptor vlf wanted ...

[Qiaozhi]

I forgot to mention when I said "Print" I meant with a CnC Pen plotter, UV laser plot on to dry film, or expose image on to dry film with UV projector, nonetheless I think my question was answered, If I was to use a laser printer ink transfer method, I would leave as is, but in my case, it needs to be mirrored, due to the fact I am plotting (drawing) directly to the PCB copper board and not a sheet of photo paper.

If you are cnc engraving the PCB, then (of course) you need to flip over the image. Then the components are inserted on the side where there are no PCB tracks. The same applies to the ink transfer method.
However, if you're submitting the Gerber files to a PCB manufacturer, the files remain as they are. The manufacturer knows that the bottom layer needs to be flipped.

[Tibuck19]

The figure on page 114 is a view of the bottom (copper) layer looking through the PCB from the top. In other words, you're looking at the component side of the board. There is no need to flip the board over. This is the same view you get in the PCB package. All layers are viewed through the board.

I forgot to mention when I said "Print" I meant with a CnC Pen plotter, UV laser plot on to dry film, or expose image on to dry film with UV projector, nonetheless I think my question was answered, If I was to use a laser printer ink transfer method, I would leave as is, but in my case, it needs to be mirrored, due to the fact I am plotting (drawing) directly to the PCB copper board and not a sheet of photo paper.

[Tibuck19]

The figure on page 114 is a view of the bottom (copper) layer looking through the PCB from the top. In other words, you're looking at the component side of the board. There is no need to flip the board over. This is the same view you get in the PCB package. All layers are viewed through the board.

Thank you.

[Qiaozhi]

when I print out the Bottom copper, as a reference on Page 114, R1,R2,R8 will need to be on the bottom left side correct? so when I flip the board to place the components R1,.... will be place on top left? here a reference to what i'm asking .

[ATTACH]44856[/ATTACH]

The figure on page 114 is a view of the bottom (copper) layer looking through the PCB from the top. In other words, you're looking at the component side of the board. There is no need to flip the board over. This is the same view you get in the PCB package. All layers are viewed through the board.

[Qiaozhi]

... if you still have the TR detector one, that be nice!

All the Gerber files are here ->

http://www.geotech1.com/forums/content.php?144-gerber-files

[Tibuck19]

I found the Gerber files in the forums for the Raptor, if you still have the TR detector one, that be nice! when I print out the Bottom copper, as a reference on Page 114, R1,R2,R8 will need to be on the bottom left side correct? so when I flip the board to place the components R1,.... will be place on top left? here a reference to what i'm asking .

[Tibuck19]

You can buy direct from here -> Inside the METAL DETECTOR - Published September 2012 (It's actually the 3rd link down on the Forum page.)
Depending where you live, you will need to order from either Carl or myself. Ordering details are included in the link.
Otherwise, you can buy from eBay UK, or Amazon UK.

Is it still possible to get the Gerber files for the board layout for the Raptor and the TR detector on Chapter 8 please ?

[Qiaozhi]

There's a link on ebay

You can buy direct from here -> Inside the METAL DETECTOR - Published September 2012 (It's actually the 3rd link down on the Forum page.)
Depending where you live, you will need to order from either Carl or myself. Ordering details are included in the link.
Otherwise, you can buy from eBay UK, or Amazon UK.

[kara1453]

There's a link on ebay

[WM6]

I'd like to buy the book

Good decision, go to post #2 from Qiaozhi. You can (usually) find this book on eBay too (payment by Paypal) or at Amazon:

http://www.amazon.co.uk/Inside-Metal-Detector-In-depth-Technology/dp/098583420X

[kara1453]

I'd like to buy the book

[WM6]

Hi, I'd like to mail a book pay shall

You want to buy (purchase) ITMD book, or you want to sell copy-parts of ITMD book to others? Can you be more clear?

[kara1453]

Hi, I'd like to mail a book pay shall

[mst]

My own technology
is enough for me.......thanx......

[mst]

ok ...sorry....