Announcement

Collapse
No announcement yet.

For sale bare boards for Delta Pulse/Sniffer XR-71

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • kt315
    replied
    i do not want to know what you change.

    i asked you to measure the voltages.
    you see yourself - NO POWER SUPPLY ON THE BOARD. ABSENT.
    begin to fix the problem.

    Leave a comment:


  • chuubaba
    replied
    I already changed VD7, VD8, VD9.

    Leave a comment:


  • kt315
    replied
    nice seek the problem. has to be
    +E - +10V
    GND - +5V

    Leave a comment:


  • chuubaba
    replied
    Originally posted by kt315 View Post
    desolder mosfet.
    set tester probe in control point -E, another probe in GND and after in +E. write what you see.
    tester range 20V, DC.
    -E 0.08v and +E 0.18v

    Leave a comment:


  • kt315
    replied
    desolder mosfet.
    set tester probe in control point -E, another probe in GND and after in +E. write what you see.
    tester range 20V, DC.

    Leave a comment:


  • chuubaba
    replied
    Surprised to learn remoteness an issue for expert.
    All was working fine when i changed C3 from 15nf to 18nf and the tone changed and red LED blinked when DEPTH pot to near full.
    Then I installed new block connectors.
    I also touched up solder of R52.
    Next i power the board but no green or red LED, no detection, no tone.
    Next i replaced MOSFET, all IC, DA7, VD7,VD8,VD9 but no success.

    Leave a comment:


  • Andi68
    replied
    This is an infinite story

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by chuubaba View Post


    BTW which transistor drives MOSFET? I want to replace it.
    Originally posted by chuubaba View Post
    Yes i saw his answer and i am waiting for his diagnosis.
    As i said before your knowledge about electronics is equal to mine because you also can't figure out what is problem with this board.
    To try and diagnose a fault remotely is extremely difficult, especially when the person at the other end doesn't know what they're doing. Even with the best will in the world, you're chances of getting this working are very slim. Do you not have a friend nearby who can assist you?

    Leave a comment:


  • chuubaba
    replied
    Originally posted by Qiaozhi View Post
    Beyond hope, I'm afraid.
    Did you not see KT's answer below? There is no transistor.
    Yes i saw his answer and i am waiting for his diagnosis.
    As i said before your knowledge about electronics is equal to mine because you also can't figure out what is problem with this board.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by chuubaba View Post


    BTW which transistor drives MOSFET? I want to replace it.
    Beyond hope, I'm afraid.
    Did you not see KT's answer below? There is no transistor.

    Originally posted by kt315 View Post
    longest rip away you send him seeking this transistor. DP mosfet is driving directly from/by NE556.

    Leave a comment:


  • kt315
    replied
    Originally posted by dbanner View Post
    Sorry Chuuby, I couldn't resist.

    Click image for larger version

Name:	itmd.jpg
Views:	4
Size:	142.6 KB
ID:	355442

    Leave a comment:


  • chuubaba
    replied
    Originally posted by kt315 View Post
    longest rip away you send him seeking this transistor. DP mosfet is driving directly from/by NE556.
    I changed all the IC but not working.

    Leave a comment:


  • Andi68
    replied
    Now I am very sad.

    I wanted to relieve my best friend KT315

    Leave a comment:


  • chuubaba
    replied
    No problem Andi. At least you decided to help. Thank you man.

    Leave a comment:


  • dbanner
    replied
    Originally posted by Andi68 View Post
    Ouch, I do not have a schematic in front of me, sorry

    Leave a comment:

Working...
X