SMT Bandito Info/Build

[CDI]

hello guys anyone try make this PCB of Bandido??
[ATTACH]34700[/ATTACH]

Omg, looks amazing. Where did u found this pcb? Can u give link? Thx

[Toros]

hello guys anyone try make this PCB of Bandido??
[ATTACH]34700[/ATTACH]

This is an very interesting board. It can be found in the Sprint layout version?

[seadoggy]

hello guys anyone try make this PCB of Bandido??

[CDI]

And this one is original by GSL from md4ru which i redesigned.

[CDI]

Hello, someone have the PCB designe but, through hole?, I saw the schematic, and I would like to make it?[ATTACH]34689[/ATTACH]

Long time ago, i redesigned this one by GSL from md4ru site. But, i cannot confirm if there are errors, cause i never finished my board.
Here is, somebody can check if there is a mistake on pcb. That version was trough hole, except resistors, i just added trough hole resistors.

[hectorvillic]

Hello, someone have the PCB designe but, through hole?, I saw the schematic, and I would like to make it?BandidoIIuMax.pdf

[kt315]

thank you Koala and Thomas for the info.

[seadoggy]

I have looked at my board and I see some modifications but not really any errors. Please remember that since the PCB is single-sided, I ran into problems getting signals from one part of the circuit to another and used wires. There are several short "Jumper" wires and a few longer wires. There were called out on the schematic and the PCB layout I posted. Example : Wire A to Wire A. On the back of the board, I added 2 small capacitors to simply tweak the ground balance. I had to do that to get the range of ground balance without being right at the end of potentiometer travel. I also added on the bottom of the PCB a short wire to connect a pin to ground. I mechanically engraved my PCB and sometimes there is not enough copper left in an area and a pin gets isolated even though the layout shows it is grounded. It was just a side effect of my mechanical etching. If your are using conventional chemical etching, your PCB should be fine. I will include some pics.[ATTACH]34685[/ATTACH][ATTACH]34686[/ATTACH]

Ok thx mate on nice pics i will try make and see what will happened

[Merc]

I have looked at my board and I see some modifications but not really any errors. Please remember that since the PCB is single-sided, I ran into problems getting signals from one part of the circuit to another and used wires. There are several short "Jumper" wires and a few longer wires. There were called out on the schematic and the PCB layout I posted. Example : Wire A to Wire A. On the back of the board, I added 2 small capacitors to simply tweak the ground balance. I had to do that to get the range of ground balance without being right at the end of potentiometer travel. I also added on the bottom of the PCB a short wire to connect a pin to ground. I mechanically engraved my PCB and sometimes there is not enough copper left in an area and a pin gets isolated even though the layout shows it is grounded. It was just a side effect of my mechanical etching. If your are using conventional chemical etching, your PCB should be fine. I will include some pics.

[seadoggy]

That was my PCB layout. I still have the machine with this PCB and I still use it. I don't remember if I had to correct any mistakes on it or not. I can open the machine and look if needed. It's still my favorite machine.

Merc

ok mate can you pls open and see i make holes in pcb and i start to solder parts,but idk if pcb have mistakes!thx alot


I have also this version but idk is okk

[Thomas]

http://www.ebay.com/itm/PLANO-4648-L...sAAOSwhcJWJQkc

I don't know what size your looking for, but what ever you get, make sure it has the 3 grips to hold the top on.

I have a bunch of these, all different ones but not as good as the plano The link goes to the smart phone ones just keep digging you'll get to the bigger ones.

http://www.ebay.com/itm/Outdoor-Prod...r=500393741771

[Koala]

can anybody give a link where to buy such submersible box? http://www.ebay.com/itm/TESORO-BANDI...oAAOSwYaFWcF53

Do a Google for "pelican 1040 case" loads here in the UK but don't know if they will ship to you for a reasonable price

[kt315]

can anybody give a link where to buy such submersible box? http://www.ebay.com/itm/TESORO-BANDI...oAAOSwYaFWcF53

[Merc]

That was my PCB layout. I still have the machine with this PCB and I still use it. I don't remember if I had to correct any mistakes on it or not. I can open the machine and look if needed. It's still my favorite machine.

Merc

[seadoggy]

I have Rev.1, but I have no idea how good this PCB is

Thx alot i also get one version from member here on geotech