Pulse Star II (first analog version)

[55323352]

Dear Mr. Yves Corniel,

I hope this message finds you well.

I am a hobbyist and outdoor treasure hunter who has long been deeply interested in your Pulse Star II metal detector. I am especially curious about its legendary deep detection performance.

I am writing to respectfully ask if you would be willing to share the schematic and PCB layout files for the Pulse Star II, including the complete Gerber files, source files, and SMT BOM/coordinate files. I would like to build one for myself as a DIY project.

I am a true enthusiast and would greatly appreciate your help. You can reach me at my email: [email protected]

Thank you so much for your time and consideration.

Best regards,

[Detectorist#1]

Yes, TL431 have to be placed in reverse of REF25Z. The hole for MINUS of REF25Z have to be used for MINUS of TL431. The hole for PLUS of REF25Z have to be used for PLUS of TL431. The third hole under REF25Z (not connected anywhere ) will rest not used.

[Ssqqar12]

Hi Ssqqar12,
No problem to use TL431 instead of REF25Z. Just solder it on the board according this scheme.

Hi Ssqqar12,
No problem to use TL431 instead of REF25Z. Just solder it on the board according this scheme.

This means, according to the modification, it is placed in reverse.I mean the opposite of negative and positive according to the diagram you drew.

[Detectorist#1]

Hi Ssqqar12,
No problem to use TL431 instead of REF25Z. Just solder it on the board according this scheme.

[algan]

Je cherche le pcb pdf please puls star 2

I have a few remaining boards for the Pulse Star II. I am sending a pcb pdf with the boards to make it easier for you to fill in. Greetings, and this is the link where you can place your order.
https://www.ebay.com/itm/116940184738

[ivconic]

KT's very wise suggestion!

[kt315]

Je cherche le pcb pdf please puls star 2

cherche le femme

[jakob leo]

Je cherche le pcb pdf please puls star 2

[Ssqqar12]

Please advise me, I don't have a ref25z, how do I mount a TL431 on the same pins?

[algan]

Some time ago I bought two boards like the ones mentioned in this post: https://www.geotech1.com/forums/foru...591#post435591.
I assembled one and it worked correctly, but apparently they are no longer for sale.

I have several boards.
https://www.ebay.com/itm/116806195369

[Jose]

Some time ago I bought two boards like the ones mentioned in this post: https://www.geotech1.com/forums/foru...591#post435591.
I assembled one and it worked correctly, but apparently they are no longer for sale.

[kece hon]

Here are the photos of the Pulse Star 2 Pro. It can be seen that it has two processors these days since I repaired it and tested its depth. On the way, I will see the pulse width and frequency and other parameters.

Hi, Thanks for every comment your observation are very valuable
Can you please share The SMD PCB lay file version That you have posted
Thanks again

[Farzadshaker]

Hello to all friends... Respected teachers... I wanted complete information about Pulse Star 2 and Pulse Star 2 Pro. Teachers who have complete and flawless information about these two models and versions, (schematics, PCP... and all complete information) I will buy Tether and any other cryptocurrency by paying the fee. Thank you.

[algan]

How are you my friends?

I bought this Plus Star 2 board and I don't know how to connect the switches. Is there a drawing of the switches so that they are clear on how to connect them?

This is how it connects, there's nothing complicated

[pigeon]

How are you my friends?

I bought this Plus Star 2 board and I don't know how to connect the switches. Is there a drawing of the switches so that they are clear on how to connect them?

Where did you buy it? Thank you very much, brother.