Non motion detector

[ivconic]

Thank you great master for sharing.You share your projects here and give them to us.no one does this, most people don't do it thank you .You are a very nice person.You have a heart of gold.
Grandmaster ivconik.

Thanks, but this time it was Carl's idea to start this topic.
I like to share idea and to see other people working on it too.
More people = more opinions = more ideas and solutions.

[cnckecgo]

Thank you great master for sharing.You share your projects here and give them to us.no one does this, most people don't do it thank you .You are a very nice person.You have a heart of gold.
Grandmaster ivconik.

[ivconic]

[ivconic]

[Carl-NC]

Yup

[ivconic]

Like this?

[Carl-NC]

And it would look like this:

[ATTACH]57365[/ATTACH]

Swap the positions of R14 & U3a so there is a better balance of charge injections. I should have done this in my drawing.

This is the Whites 3900 reset circuit, which I used in some old projects of mine that I did a long time ago.

This is basically the same circuit Tesoro used, except that the SPDT switch probably improves charge injection at switch-over.

[vahit05]

İ have fail to place 353 and 393.and than circuit is no voice..ayrıca paylaşımın i?in teşekk?rler ?stad

[ivconic]

There is some crazy force that likes to joke with us and our lives ... that's what it looks like ...
Because today I complained about CNC ... and after that post I forgot about it and did other things.
Two hours later, a car was parked in front of the house. An old friend I haven't seen in a long time.
I go out to meet him, he calls me from behind the car, opens the trunk and I have something to see;
a new unused cnc machine, the same as mine ...
he says "I bought it for no reason, I don't use it, I don't need it, here you are, do with it what you want ..."
And so now I have two of the same cnc machines, on this one from today there is a new unused laser ...
Should I give it up and not try again ... or should I try to work with this laser as well?
Now those will stand in front of my eyes ... two instead of one...

Isn't God a prankster ?!


P.S.
Let me start complaining fiercely about Deus ... by hard whining and beating my chest ...
maybe pull my hair out of annoyance... and maybe tomorrow someone will bring Deus 2!

[ivconic]

[ATTACH]57369[/ATTACH]

Oh man!
Don't use that greasy paste!
Since you already did it; wash the whole pcb in nitro resin, wash it good!
That greasy paste is not good for soldering such electronics, at all.

[ivconic]

[ATTACH]57369[/ATTACH]

So fast!

[vahit05]

[ivconic]

I don't have a video, because I used this reset circuit more than 10 years ago in an old project and at that time I didn't make any video. This works just like the Whites 3900 detector, which is a static mode detector with very good stability. I also implemented this reset circuit in the PI Delta Pulse detector in the past and it worked quite well and I also don't have any recorded videos of the work. If you search YouTube for videos of the Whites 3900 detector, you will see the actual operation of this reset circuit, which I believe to be one of the best and most stable reset circuits I have tested so far.

Oh i do know how 3900 works. I had 2-3 original detectors so far.
One of those i traced out and posted schematic and pcb on this forum... a while ago.
It suffers from the drifts also...

[ivconic]

I will deviate a little from the topic, just to entertain those present ...
Until I had CNC; I dreamed that one day I have a small desktop CNC and work with it instant pcb!
And then last year I bought a new desktop CNC.
This one:

https://www.amazon.co.uk/Mostics-lasermodule-Engraving-CNC3018PRO-Engraver/dp/B07VCV18X5

Due to the force of inertia, I first played with the laser. Because it's a lot easier.
But there was a disaster, after less than 4-5 hours of total work (within 20 days), the laser burned out! ??
So much for the reliability of Chinese products ...
All unhappy I then switched to a spindle option.
I tried to establish an easy pcb engraving method with that.
In a couple of attempts I destroyed a couple of tools (there are 20 of them in the set) and then all angry and disappointed I definitely gave up!
And since then, that CNC machine has been standing on my desk, collecting dust ... and every time I look at it; I get annoyed and angry!
I don't have to mention that I watched countless Youtube demonstrations, "how to ..." and similar material at the time.
The characters succeed in everything they try ... but nothing from those works to me!
For a long time I made pcb by myself, or by hand drawing with a marker or nail polish ... then I switched to transfer foil ...
None of this was "accepted" for me as a reliable method for pcb.
In the end, I realized that it is better to pay someone else to do it for me.
When I do "serious" things in multiple copies; pcb i order in China through already well known services.
But when I'm working on a prototype, I'm developing something new ... I'm forced to have someone do my PCB ... as a rule; someone who is lazy, late, lies and I'm last in his priority.
"The life of us artists is hard" ....

[eduardo1979]

I don't have a video, because I used this reset circuit more than 10 years ago in an old project and at that time I didn't make any video. This works just like the Whites 3900 detector, which is a static mode detector with very good stability. I also implemented this reset circuit in the PI Delta Pulse detector in the past and it worked quite well and I also don't have any recorded videos of the work. If you search YouTube for videos of the Whites 3900 detector, you will see the actual operation of this reset circuit, which I believe to be one of the best and most stable reset circuits I have tested so far.