SURF PI HELP

[daverave]

daverave, please read this pages. I hope George and Carl would not be angry on me if I give a quotation for the book. but it is a determining of SAMPLE DELAY.
it is in english and it is VERY CLEAR reading for you, not for me...

[ATTACH]26687[/ATTACH]

thanks for that...as a matter of interest can this book be bought from a shop or where would i buy this ??????

[kt315]

daverave, please read this pages. I hope George and Carl would not be angry on me if I give a quotation for the book. but it is a determining of SAMPLE DELAY.
it is in english and it is VERY CLEAR reading for you, not for me...

[daverave]

you do not answer me... you need tune a board's pot on 12-15us edge of SAMPLE DELAY... (while a second pot would be in zero Ohm position) THIS IS THE PRE-SET POT. while your second pot at panel you use for operative tuning from this value 12-15us (minimum of the preset) to 30 or more... or what you get there....


[ATTACH]26677[/ATTACH]

ive got myself confused....i have the silver dog surf pcb and instead of having a 10k preset on the pcb i have wired in an external pot and fixed on my control box....so i can adjust pulse delay...have i done this wrong ??????

[kt315]

[Qiaozhi]

ive never seen this version of the hammer head before...very interesting 2 stage preamp....is this pcb and pic availiable to buy ???? i noticed also in the new whites dual field the engineer claims that depth has been increased by more gain on the dc amp making weak signals more stronger.

Carl might have some PCBs left. You'll need to ask.
The hexcode for the PIC is attached.

[kt315]

mine is set fully anti clockwise early

you do not answer me... you need tune a board's pot on 12-15us edge of SAMPLE DELAY... (while a second pot would be in zero Ohm position) THIS IS THE PRE-SET POT. while your second pot at panel you use for operative tuning from this value 12-15us (minimum of the preset) to 30 or more... or what you get there....

[daverave]

i noticed with the hammer head diagram there is option for vco/non vco audio...can a switch be added so you can switch from vco to non vco or viceversa

[daverave]

To improve depth, you really need to have a 2-stage preamp. At the moment the preamp has a large gain of 60dB (1000x), but earlier sampling could be achieved if you were to split the preamp over two opamps, each with a gain of 30.4dB (33x). Have a look at the attached Hammerhead II schematic as an example.[ATTACH]26676[/ATTACH]

ive never seen this version of the hammer head before...very interesting 2 stage preamp....is this pcb and pic availiable to buy ???? i noticed also in the new whites dual field the engineer claims that depth has been increased by more gain on the dc amp making weak signals more stronger.

[daverave]

daverave, can you give me direct link on your surf pi schematic you mean on here? have you INSIDE THE METAL DETECTOR I could point you a page for reading what is SAMPLE DELAY?

Its the one on here...i know about sample delay...mine is set fully anti clockwise early...im a bit concerned the coil i made has not needed any more damping....no ringing with the 390 ohm resistor as in original spec for surf pi...my back emf is very steep and not much curve....i wonder do i need to experiment with damping resistor....my coil is 15 x 12 400 uH....5 ohm coil......i used 18T of 30 swg wire

[Qiaozhi]

To improve depth, you really need to have a 2-stage preamp. At the moment the preamp has a large gain of 60dB (1000x), but earlier sampling could be achieved if you were to split the preamp over two opamps, each with a gain of 30.4dB (33x). Have a look at the attached Hammerhead II schematic as an example.

[kt315]

daverave, can you give me direct link on your surf pi schematic you mean on here? have you INSIDE THE METAL DETECTOR I could point you a page for reading what is SAMPLE DELAY?

[daverave]

[QUOTE=Qiaozhi;178752]

Please be aware that the audio frequency is derived from the TX oscillator. Which means that increasing the pps rate to 1500 will give the audio output a correspondingly higher tone.

im just a little dissapointed cause i thought using a coil of 15 x 12 and getting the capacitance lower i would get a bit better depth...i know people who have the whites dual field who get really good depth on gold items...i will experiment first with another surf pcb and compare...i know eric foster used 1500hz on one of his gold quest machines...i know the surf pi is different cause audio is derived from the tx oscilla tor...not sure if i could put up with 1500hz in my ears

[Qiaozhi]

[QUOTE=daverave;178750]

What works for me when adjusting the DC OFFSET with surf pi and baracuda is this
move coil away from all metal
put the multimeter on DC volts,
place the black negative lead of multi meter on negative battery
place the red positive lead on pin 6 and adjust to zero DC volts

ive adjusted the dc offset as you stated but in my workshop lots of metal in the room so not easy to do spot on...although ive almost finished this project im thinking of experimenting with another pcb and increasing the frequency to 1500 hz and maybe slighty increase tx power as im not entirely satisfied with the depth im getting with the surf pi considering im using a 15 x 12 coil....im getting around 12" on a uk 50p coin....and around 6-7" on thin section 9ct gold ring.....whats your expert advice to me as a novice detector builder.

Please be aware that the audio frequency is derived from the TX oscillator. Which means that increasing the pps rate to 1500 will give the audio output a correspondingly higher tone.

[daverave]

[QUOTE=6666;178743]What works for me when adjusting the DC OFFSET with surf pi and baracuda is this
move coil away from all metal
put the multimeter on DC volts,
place the black negative lead of multi meter on negative battery
place the red positive lead on pin 6 and adjust to zero DC volts

ive adjusted the dc offset as you stated but in my workshop lots of metal in the room so not easy to do spot on...although ive almost finished this project im thinking of experimenting with another pcb and increasing the frequency to 1500 hz and maybe slighty increase tx power as im not entirely satisfied with the depth im getting with the surf pi considering im using a 15 x 12 coil....im getting around 12" on a uk 50p coin....and around 6-7" on thin section 9ct gold ring.....whats your expert advice to me as a novice detector builder.

[6666]

What works for me when adjusting the DC OFFSET with surf pi and baracuda is this
move coil away from all metal
put the multimeter on DC volts,
place the black negative lead of multi meter on negative battery
place the red positive lead on pin 6 and adjust to zero DC volts
I hope that works for you.
Cheers
6666