VDI-RODERICO

[scrungy_doolittle]

That zolen display looks great. I just snagged two off ebay.

[scrungy_doolittle]

I hate SPI, but they do save pins. I'm not understanding the issues with backlights. Typically, a monchrome lcd needs the backlight for the display to be visible. I know that it is absolutely the case for color displays. I've been working with a 128x160 color display. Don't know what it would look like in sunlight, but they are all over the place on ebay...

[roderico]

that display also looks good to me, in principle it should work and it does not have the problem of the backlight, the zolen display from ebay is smaller and lighter but probably it needs to be disassembled to cut the K pin of the backlight...

[kroman01]

words of appreciation ... I did not think it would be so fast, I am at the stage of ordering the display, I thought it should be good

http://www.artronic.com.pl/o_produkcie.php?id=1153

[roderico]

this is the firmware 2.1 + ST7567/ST7565 driver for testing, the display should be connected to the vdi pcb as follows:

CSTB (e.g. /CST) -> CS1
RSTB (e.g. /RST) -> RST
A0 (e.g. D/I) -> C/D
RWR (e.g. /WR) -> R/W
ERD (e.g. /RD) -> EN

The configuration pins if they are not set should be

PSB -> High (parallel)
C86 -> Low (8080-series MPU)
SEL[2:1] -> Low, Low (1/65 duty)

the rest of the pins have the same name, CS2, V0 and VEE are not used, the lcd contrast is controlled by software, only tested with the zolen display (5V+parallel). The only issue found is that the backlight control does not work because the K- pin is connected directly to VSS in the display pcb.

[roderico]

parallel and 5V, these firmwares will only work with parallel interfaces because they have lower latency and do not need 128x64/8 = 1024 bytes of additional memory in the microcontroller (e.g. PIC18F25K22 has only 1536 bytes)

[kroman01]

what serial or parallel interface you used on this display "zolen"

[roderico]

I have adapted the code and the zolen display from ebay seems to work well with 5V, the only issue I have found so far is that it has no K- pin to control the backlight, a possible solution could be to cut the K- track on the display and connect it to the vdi to make it work, once I implement the contrast control I could upload a testing firmware for the ST7565 controller

[Altra]

I not sure what to make of it? View the revisions on the last page of datasheet "Version 1.0a - Modify Logic power supply VDD - VSS = 4.0V to 5.5V, VOUT= -18V" . Newer datasheets do not show the older revisions

http://www.hpinfotech.ro/ST7565.pdf

The displays I have been using at +5 volts are controlled by SPLC501C that is a clone of the ST7565 which can use the same drivers.
Datasheet claims 2.4v to 5v operation

https://www.newhavendisplay.com/app_notes/SPLC501C.pdf

[roderico]

ok, I can write the driver for the ST7567 controller, I have one of this zolen displays I never used that claims to be 5V, if it works it should also work with your display (http://www.blaberk.com.pl/arduino/DEM128064O.pdf) but you would need to do the conversion from 5V to 3V

[kroman01]

a simple converter can be made with the help of resistors see how it was solved in Fortune_Pro_2 it is a serial interface

https://drive.google.com/drive/folders/1MbvcaFgtOmQCRL8sOqSOIiBTMBLv-jrv

[roderico]

I just received a couple of these displays. They feature the ST7565 controller, 3.3 to 5v operation, serial or parallel. Also comes mounted on a pcb so no soldering a 0.5mm spacing smd connector. The serial pins are D6, D7 not shown on the ebay listing

https://www.ebay.com/itm/1pcs-New-12...gAAOSwbw1aHWC7

on another ebay listing they link this datasheet for the same display

https://www.surenoo.com/surenoo_store/download/display/ZLE12864B-FFSSWE-NAA.pdf

which is for a ST7567 controller and both work with 3V, however it is not clear to me in the datasheet if the display needs an external converter to accept 5V for VDD without damaging the chip or if it is included in the display. In any case, it would only need to write a driver and maybe the external level converter to make it work, if there is interest in this display I could write the driver for v2.2

[kroman01]

yes I know that NT7108, S6B0708, RA8808 are compatible but I found displays with S6B0108 at a good price

http://www.wincomlcd.com/pdf/WG12864D%20V1.0-SFYLYHTC06.pdf

[roderico]

those might work, I think NT7108, S6B0708, RA8808,... controllers are also compatible

[Altra]

I just received a couple of these displays. They feature the ST7565 controller, 3.3 to 5v operation, serial or parallel. Also comes mounted on a pcb so no soldering a 0.5mm spacing smd connector. The serial pins are D6, D7 not shown on the ebay listing

https://www.ebay.com/itm/1pcs-New-12864-128x64-Graphic-COG-LCD-Display-module-ST7565P-Free-Shipping/322589512522?epid=6010515363&hash=item4b1bd5534a:g:ZUgAAOSwbw1aHWC7