BARACUDA-Legend-1

[Old cart]

Nothing change, change R5 ,6 and 7. .. still beeping on tilt
I should wait CD40106 replacement.

Original [ATTACH]36362[/ATTACH]
Change [ATTACH]36361[/ATTACH]

I SEE THE PROBLEM. The resistors numbering has changed in the new schematic.

First put back the resistors where they were! Be careful. Every time you unsolder the pads get weaker.

R5= R19 on your board connects to pin 1
R6= R17 pin 5
R7=R18 pin 3

Double check these. You must go by the PIN numbers.
It is also wise to replace the 40106 but it will not hurt to try this mod. If it does not work then do the 40106 replacement.
Sorry for the confusion.

[ripsdevala]

Nothing change, change R5 ,6 and 7. .. still beeping on tilt
I should wait CD40106 replacement.

Original
Change

[ripsdevala]

Double post, bad net

[ripsdevala]

Thaks for the clue old chart, I will learn it again.

I dont have a scope, just analog multimeter. what I learn from the discussion is, that the original is work normal, some builder have trouble because something else.

But what i read from the back that this project normaly have sensitive to coil tilt or sweep.
Let me see what i can do with the clue, or I just take the sweep & beep.

De vala

[Old cart]

I have read the rest, what i can see is just cut and bridge, the two resistor is 270 and 270k like the original but put at the bottom, right?.
And caps modification.... Can you show me, im not a a native english, maybe I miss reading.

Read this whole thread from the beginning

http://www.geotech1.com/forums/showthread.php?23009-Baracuda-Build-(silverdog-kit-Rev2)/page2

The schematic you want is near the end in thread in post 124. The resistors that need changing are R5,6 and 7. When you cut the trace and added the jumper you changed the reference for the timing of the 40106 chip this means these resistors need changing too.

These new values should work but they may not. These chips are not precision devices. If this does not fix the problem you wil have to adjust the values. To adjust the values requires an oscilloscope. Do you have one and know how to use it?

Note it is also likely that the 40106 has been damaged because of the power supply problems discussed in post 102.

Good luck!

[ripsdevala]

I have read the rest, what i can see is just cut and bridge, the two resistor is 270 and 270k like the original but put at the bottom, right?.
And caps modification.... Can you show me, im not a a native english, maybe I miss reading.

[ripsdevala]

You have to make all the mods. Read ALL OF THE REST OF THE THREAD. It will tell you what resistors need to be changed as well as what values they must be. If you just cut the trace and add the wire your earth field cancellation will be wrong which causes the false beeps. You will also probably have to replace the 40106 parts as they can be damaged by the original circuitry.

I see, let me work it.
Is that 170k and 270k resistor added to the bottom?

[Old cart]

And yes...its increase the treshold,but to noisy for CD40106 than HCF40106. Its help reduce the shake beeps to.
Cut and make a jumper only, im not sure what the 2 resistor is.

Thanks koala

[ATTACH]36345[/ATTACH]

You have to make all the mods. Read ALL OF THE REST OF THE THREAD. It will tell you what resistors need to be changed as well as what values they must be. If you just cut the trace and add the wire your earth field cancellation will be wrong which causes the false beeps. You will also probably have to replace the 40106 parts as they can be damaged by the original circuitry.

[ripsdevala]

http://www.geotech1.com/forums/showt...486#post215486


You could try the mod here.

And yes...its increase the treshold,but to noisy for CD40106 than HCF40106. Its help reduce the shake beeps to.
Cut and make a jumper only, im not sure what the 2 resistor is.

Thanks koala

[Koala]

http://www.geotech1.com/forums/showthread.php?22964-Barracuda-Legend-Kit-Problems&p=215486#post215486

You could try the mod here.

[ripsdevala]

i think you have the Phantom beep at the end of each direction
return Point of swing left and right

so surprise, surprise it is something normal on baracuda on real field use
it cant eleminate the earth field and gain of amp block is high enough that you get Signal from fast changing earth field

i am right?

so concentra only on the Signal that are in front of you, where you get also a beep if you swing over a second time

Hi, bernte_one, Im always read your post as lord vader voice in my mind, thanks for replying.

Is that normal? the last time I use it before full working is not beeping when i move it at any direction or shake.

[bernte_one]

i think you have the Phantom beep at the end of each direction
return Point of swing left and right

so surprise, surprise it is something normal on baracuda on real field use
it cant eleminate the earth field and gain of amp block is high enough that you get Signal from fast changing earth field

i am right?

so concentra only on the Signal that are in front of you, where you get also a beep if you swing over a second time

[ripsdevala]

new problem, every i move the coil it make sound. Did i missing something??

[Koala]

After long frustation, now..... its work!!
when i check again there is two resistor that wrong.
Its work with 9volt, i use 9v modem adaptor
25cm coin
30cm up for big object


We
Hurraaaa....hurraaa.....

Well done

[ripsdevala]

After long frustation, now..... its work!!
when i check again there is two resistor that wrong.
Its work with 9volt, i use 9v modem adaptor
25cm coin
30cm up for big object
Hurraaaa....hurraaa.....