Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    Are you using a mono coil?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Pin 2 goes to ground, not -5V.
    Hello Dear Carl
    As promised, i finished the DISC demod and captured a video on scope during moving a Iron hammer over DD-coil.
    Frist i adjust sampling as follows:
    Click image for larger version  Name:	tpsam.jpg Views:	0 Size:	138.3 KB ID:	443754
    Then i connected both preamp and Disc demod to scope
    Click image for larger version  Name:	Iron.jpg Views:	0 Size:	137.5 KB ID:	443755
    After that, i captured a video from scope with measured parameters during moving an Iron hammer. You can watch from the link:
    https://drive.google.com/file/d/1PfH...ew?usp=sharing

    I have a request, please see following picture.
    Can you guide me, what schematic ( i remember that you told me that it can be a simple amplifier with gain pot as Iron sensitive pot) do you suggest me to add between the demod and 2n3904 for blanking audio ( inside the box)?
    Thank you.

    Click image for larger version  Name:	demod.png Views:	0 Size:	651.6 KB ID:	443756

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Pin 2 goes to ground, not -5V.
    Thank you.
    Click image for larger version

Name:	txsample.jpg
Views:	109
Size:	100.9 KB
ID:	443644

    Leave a comment:


  • Carl-NC
    replied
    Pin 2 goes to ground, not -5V.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Always read the data sheet. The 74221 has 2 trigger inputs, A and B:

    Click image for larger version

Name:	image.png
Views:	142
Size:	23.9 KB
ID:	443620​
    The 555 pulse is fed to the B input (pin 2); when it goes high (to turn off the TX) the 74221 is triggered. What you want is to trigger the 74221 on the falling edge of the 555 (which turns on the TX). You will have to feed the 555 signal to the A input (pin1) instead, and then tie the B input to the high side (ground in this case).
    Thank you.
    I think your means is this,
    Click image for larger version

Name:	74hc.jpg
Views:	119
Size:	46.1 KB
ID:	443622

    Leave a comment:


  • Carl-NC
    replied
    Always read the data sheet. The 74221 has 2 trigger inputs, A and B:

    Click image for larger version

Name:	image.png
Views:	142
Size:	23.9 KB
ID:	443620​
    The 555 pulse is fed to the B input (pin 2); when it goes high (to turn off the TX) the 74221 is triggered. What you want is to trigger the 74221 on the falling edge of the 555 (which turns on the TX). You will have to feed the 555 signal to the A input (pin1) instead, and then tie the B input to the high side (ground in this case).

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That looks better.
    Dear Carl
    My friend is programing for adding TX sampling.
    But i want to test by 74hc221 until his work is finished.
    Please see attached, i tested the schematic, but the sample pulse can not locate on TX ( Can't go back any further).
    Click image for larger version

Name:	TPTX.jpg
Views:	114
Size:	126.3 KB
ID:	443612
    I changed C15 by 1n, 100P and 10P and R29 by 100R. No result.
    Do you have any suggestion for adjusting the sample pulse to TX?
    Click image for larger version

Name:	74hc.jpg
Views:	135
Size:	45.0 KB
ID:	443611

    Leave a comment:


  • Carl-NC
    replied
    That looks better.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    It looks like U3a is railed out, I have no idea why. Show the waveform at TP2.
    Thank you dear Carl.
    I checked again and found my mistake, TX was not worked. I fixed it.
    TP8 and TP9 as follows:
    Click image for larger version

Name:	TP8,9.jpg
Views:	130
Size:	129.5 KB
ID:	443581

    Leave a comment:


  • Carl-NC
    replied
    It looks like U3a is railed out, I have no idea why. Show the waveform at TP2.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Either one will work.
    Hello
    Dear Carl
    Today, i built TX and preamp part based on the following :
    Click image for larger version  Name:	tx.jpg Views:	0 Size:	47.5 KB ID:	443570
    For first testing in my preamp output, i tested it with mono coil (500uH+680R)​.
    Form of my Tp8 is as
    Click image for larger version  Name:	Tp5.jpg Views:	0 Size:	112.2 KB ID:	443571
    And my Tp9 is as
    Click image for larger version  Name:	Tp4.jpg Views:	0 Size:	105.3 KB ID:	443572
    I think my TP8 and TP9 is not correct because its pulse is showing only receiving pulse and (it is very long).
    Do you have any suggestion for checking?
    Do you think i should reverse invert/non-invert of 5532 (pin 2 and 3)?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Either one will work.
    Thank you. I will measure output voltage of DISC and will try to capture a video from ferrous/non-ferrous.
    So, you will see better and help me how to figure out its final amplifier stage for blank audio.
    Thank you dear carl for all supporting and your posts.

    Leave a comment:


  • Carl-NC
    replied
    Either one will work.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    I have no idea what kind of amplifier you need or how much gain or anything else. You really need to build the extra demod stage and see what the "iron signal" looks like before you try to figure out what to do with it. I'm pretty sure you will not be able to design a complete circuit, build it, and have it work on the first try. Build it a little at a time, and figure out the next steps as you go.
    Actually, i have doubt about connecting TP8 or TP9 to my DISC demod.
    For better understanding (before making PCB), i simulated it with a pulse input (initial (low) voltage 0V and pulsed (high) voltage 5v).
    You can see my pulse setting as follow:

    Click image for larger version  Name:	pulseset.jpg Views:	0 Size:	50.7 KB ID:	443132

    The simulated schematic is as following:
    Click image for larger version  Name:	sim.jpg Views:	0 Size:	172.3 KB ID:	443130
    And the its scope is as follow:
    Click image for larger version  Name:	scop1.jpg Views:	0 Size:	101.5 KB ID:	443131
    If i change my pulse as initial (low) voltage -5V and pulsed (high) voltage 0v, Scope output will be as follow:
    Click image for larger version

Name:	scop3.jpg
Views:	150
Size:	103.4 KB
ID:	443134
    According to the result and form of TP8 and TP9 (positive and negative preamp out), do you think which of TP8 or TP9 should be connected as input to DISC channel and sample it?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    I have no idea what kind of amplifier you need or how much gain or anything else. You really need to build the extra demod stage and see what the "iron signal" looks like before you try to figure out what to do with it. I'm pretty sure you will not be able to design a complete circuit, build it, and have it work on the first try. Build it a little at a time, and figure out the next steps as you go.
    OK. First i will build DISC part and measure its output when it detects IRON.
    I will notify here, then i hope you can help me for adding the amplifier stage with sensitivity control.
    I also simulated TX + preamp part on software. You can see its output on scope as following :
    Click image for larger version

Name:	scop.jpg
Views:	173
Size:	96.4 KB
ID:	443119

    Channel A ( yellow) is pulse generation (0 / -5V).
    Channel B (Blue) is TP8 on schematic #526.
    Channel D (Green) is TP9 on schematic #526.
    Do you think it is correct TP8 and TP9?

    Leave a comment:

Working...
X