Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    There is a very good chance that your Chinese TL072 is not a TL072 at all. I bought some Chinese TL071 opamps, they were not TL071. Even worse, whatever they were they were a dual opamp, not even a single. I threw them away.

    When you open SW2 it is critical that IC8 has ultra-low bias current or it will quickly rail out, and that sounds like what is happening.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Where did you buy your opamps?
    Is it possible to add a meter (for exp. VU or uA meter) to HH1?!

    Leave a comment:


  • h9361
    replied
    Originally posted by green View Post
    Some more testing. Reply #95 has the nickel tested at 139mm (should be 108mm, I had three spacers on the desk. looks like I measured all three but used only two) integrator test_1

    1 tau, 3 tau and quarter were spaced at 54mm. The nickel spaced at 108mm. ground spaced 12 mm.

    Reducing amplifier response reduced noise at amplifier out, not so much at integrator out.
    Thanks for your explanation.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Where did you buy your opamps?
    Sorry for late replying.
    My TL072 is Chinese.

    Leave a comment:


  • green
    replied
    Some more testing. Reply #95 has the nickel tested at 139mm (should be 108mm, I had three spacers on the desk. looks like I measured all three but used only two) integrator test_1

    1 tau, 3 tau and quarter were spaced at 54mm. The nickel spaced at 108mm. ground spaced 12 mm.

    Reducing amplifier response reduced noise at amplifier out, not so much at integrator out.
    Attached Files

    Leave a comment:


  • Carl-NC
    replied
    Where did you buy your opamps?

    Leave a comment:


  • h9361
    replied
    I'm using TL072.

    Leave a comment:


  • Carl-NC
    replied
    Probably your IC8 has too much input bias current and is drifting. What are you using for IC8?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    No, I don't know.
    Hello
    Dear Carl
    I hope you are passing good days.
    I have question about SW2 (AutoTrack, Rev. D). I tested my HH1 with opened SW2 for testing pinpointing mode.
    After SW2 opened, my threshold pot don't work anymore! It works only in SW2 is closed.
    Is there any way that be able to work in pinpointing mode with THD pot, like other detectors?
    Thanks.

    Leave a comment:


  • Carl-NC
    replied
    No, I don't know.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    I have a question about GPX-5000 coils. As you know, Minelab is using litz wire for its detector. Do you know its litz details (number of strands and size awg)?!
    Download file, you can see Litz wires with its details.

    Leave a comment:


  • h9361
    replied
    Originally posted by green View Post
    Finally got around to trying a test. Thinking I should add target effect plus noise at different cutoff frequencies. Any thoughts what I might add or do different? Would like to not repeat changing cutoff frequencies to many times.

    I set first delay time(adjustable), second delay for 4us and GEB sample time for about 100us. Then adjust target sample time for minimum ground signal when GEB on.

    I see one of the target samples is seconds instead of us
    Thanks dear green.
    I used a new PCB rev. D, now i have no noise.
    Now i'm working over 4delay ground balancing (suggested by Mr. Carl.). My result is very very nice and i can work in 10us-25us with high stability over mineralization.

    Leave a comment:


  • green
    replied
    Originally posted by green View Post
    Don't know how to calculate noise at integrator out. Thinking of doing a test with my circuit to try and learn something. Coil not connected, noise caused be amplifier and the two 1k input resistors. Record p-p volts at amplifier out and integrator out at different amplifier cutoff frequencies with two different sample times. Any suggestions for improving the test?

    amplifier cutoff set by the capacitors I have
    Finally got around to trying a test. Thinking I should add target effect plus noise at different cutoff frequencies. Any thoughts what I might add or do different? Would like to not repeat changing cutoff frequencies to many times.

    I set first delay time(adjustable), second delay for 4us and GEB sample time for about 100us. Then adjust target sample time for minimum ground signal when GEB on.

    I see one of the target samples is seconds instead of us
    Attached Files
    Last edited by green; 10-26-2021, 10:53 PM. Reason: added sentence

    Leave a comment:


  • Carl-NC
    replied
    Getting the 555 timer to do that would be quite easy. Getting the coil & preamp to do that would be quite difficult.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl
    I remember that you mentioned in your article "If a 1kΩ resistor is used forR42a, the minimum pulse delay can betaken down to 8?s".
    My question is that do you think i can reach less delay, for exp, 5us or etc?
    Thanks

    Leave a comment:

Working...
X