Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    These waveforms are taken from a single preamp, but you can use a separate preamp if you want. I don't know exactly what you will need after the demod, you will first need to see what the signals look like.

    Click image for larger version

Name:	image.png
Views:	195
Size:	138.3 KB
ID:	442941​

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That circuit is used in VLF detectors, the signals are different in a PI detector. You will need to add the demodulator and then find out how that signal behaves with ferrous targets, non-ferrous targets, and ground. This includes changing the demod timing to see how that changes the signals. You should be able to find something that works well enough on at least some targets. Then compare the iron signal to the GB signal and figure out how to combine them to blank the audio. They are both motion-mode signals so you may not even need to combine them, I don't know.
    Thank you.
    But the new demod is connected to pi preamp. I think we can not see tx-on ( pulse) because Iron increases tx-on pulse. Do you think it is better to use an independent preamp?
    Since both are motion, do you think i only need to add opamp after the demod for iron reject pot?

    Leave a comment:


  • Carl-NC
    replied
    That circuit is used in VLF detectors, the signals are different in a PI detector. You will need to add the demodulator and then find out how that signal behaves with ferrous targets, non-ferrous targets, and ground. This includes changing the demod timing to see how that changes the signals. You should be able to find something that works well enough on at least some targets. Then compare the iron signal to the GB signal and figure out how to combine them to blank the audio. They are both motion-mode signals so you may not even need to combine them, I don't know.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Probably something like this will work:
    Click image for larger version

Name:	image.png
Views:	92
Size:	651.6 KB
ID:	442934​
    You will need to figure out what goes inside the box, it may be as simple as a single amplifier stage.
    Thank you.
    Do you think the following can work with Iron rejection Pot?
    And only i have an Iron rejection if first my detector detects a Metal.

    Click image for larger version

Name:	discf.jpg
Views:	121
Size:	248.9 KB
ID:	442936

    Leave a comment:


  • Carl-NC
    replied
    Probably something like this will work:
    Click image for larger version

Name:	image.png
Views:	92
Size:	651.6 KB
ID:	442934​
    You will need to figure out what goes inside the box, it may be as simple as a single amplifier stage.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Add another demodulator stage, like this:
    Click image for larger version

Name:	image.png
Views:	82
Size:	731.8 KB
ID:	442929​
    It needs to reasonably match the other demods in terms of signal delay. You will then need to figure out what to do with the new signal. One possibility is to use it to alter the frequency of the audio output so you get a very low grunt tone when iron is detected. I don't know what the rest of your circuit looks like so I cannot help with this.
    Thank you very very much for your information.
    I want to cut off audio ( silence ) if my DISC part detects any Iron (increasing voltage for TX on).
    My audio out is like the following (like Mr. Detectorist ):
    Is it possible to connect to audio so that its audio goes to silence like GPX?
    Click image for larger version

Name:	audio.jpg
Views:	112
Size:	432.0 KB
ID:	442932
    Attached Files

    Leave a comment:


  • Carl-NC
    replied
    Add another demodulator stage, like this:
    Click image for larger version

Name:	image.png
Views:	82
Size:	731.8 KB
ID:	442929​
    It needs to reasonably match the other demods in terms of signal delay. You will then need to figure out what to do with the new signal. One possibility is to use it to alter the frequency of the audio output so you get a very low grunt tone when iron is detected. I don't know what the rest of your circuit looks like so I cannot help with this.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    It looks like you are trying to add a VLF-disc circuit to a PI. All you need to do is add another demodulator to the existing PI and sample the TX-on signal from the preamp. Keep in mind this will only work for an IB coil (like DD), not a mono coil. You can try different sample points to see what works the best.
    Thank you for your guide.
    Please forgive me for my primary questions.
    You advised me to use a demodulator to existing PI and sample TX-ON.
    Please see attached, i adjusts my S1 pulse (produced by 74hc221) exactly on TX on signal from preamp (5534 output) via 4066.
    After that, there are two stages differential (TL072). Does the two stages act demodulator action that you mentioned?
    I saw your Raptor schematic and its explanation, you also used such structure for that.
    Thank you.
    Click image for larger version

Name:	demod.jpg
Views:	169
Size:	177.7 KB
ID:	442927

    Leave a comment:


  • Carl-NC
    replied
    It looks like you are trying to add a VLF-disc circuit to a PI. All you need to do is add another demodulator to the existing PI and sample the TX-on signal from the preamp. Keep in mind this will only work for an IB coil (like DD), not a mono coil. You can try different sample points to see what works the best.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes
    Dear Carl
    I remember that you posted the picture about Iron DISC when TX is on:
    Click image for larger version  Name:	image.png Views:	0 Size:	138.3 KB ID:	442897
    And please consider the following schematic for detecting Iron via increasing voltage:
    Click image for larger version  Name:	disc11.jpg Views:	0 Size:	282.6 KB ID:	442898
    First Question, Which points do you prefer to be connected to R27 and R8 (two diodes, DD Coil) to PI schematic in #Post 498?

    Second question, which of the following sampling (when TX is ON) is better (whole TX pulse or first part)?
    Click image for larger version  Name:	DT1JPG.jpg Views:	0 Size:	122.1 KB ID:	442899
    Click image for larger version  Name:	20241222_182017.jpg Views:	0 Size:	882.4 KB ID:	442900
    I simulated the DISC schematic on software and played with BW capacitors (C13 and C15).
    I make a simple Pulse generator with 100us and connected it to the differential integrated as input (following picture).
    Click image for larger version  Name:	image (1).png Views:	0 Size:	21.7 KB ID:	442901
    Then i connected its output to Scope.
    Other question, which of the triangular waveforms do you think it is better for detecting increasing voltage?
    Click image for larger version  Name:	unnamed (1).png Views:	0 Size:	139.4 KB ID:	442902
    Click image for larger version  Name:	unnamed.png Views:	0 Size:	167.7 KB ID:	442903

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes
    please forgive me for more questions.
    Thank you.

    Leave a comment:


  • Carl-NC
    replied
    Yes

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes, and yes.
    Thank you.
    In this case, can i use j6 as switching mono/DD?

    Leave a comment:


  • Carl-NC
    replied
    Yes, and yes.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post

    1. Make +VB = ground
    2. Capacitor-couple the TX signal to the preamp (as in ITMD2)
    3. Use a PMOS driver
    4. Use a floating bipolar driver
    So, i have to use this power like HHD.
    Click image for larger version

Name:	Power.jpg
Views:	152
Size:	95.8 KB
ID:	442868
    And my TX part is as follow
    Click image for larger version

Name:	preGBmain.jpg
Views:	153
Size:	94.1 KB
ID:	442869
    Is this true for DD and mono?

    Leave a comment:

Working...
X