Epe pic magnetometer

[Orbit]

Of course you can !

[alikhan]

Software

two software !same sensor 200yt!exactly the same targets 2 row and 5 impulse ![ATTACH]31061[/ATTACH][ATTACH]31062[/ATTACH]

HiI have made this magnetometer. Can any one give a hint about " how to use Geosurveior software"?Is it possible to transfer the data from logger to this software directly?All the bestAli

[spook_mer]

Hi, is there's a new version HEX file?

[rocco_k]

I want to make the scheme on Mr. ivconic

[SimonS]

here

[rocco_k]

scheme то fgm 3 simple magnetometer,Can you it publishes?
thank you

[Prospekteur]

Ok thanks a lot. It can be so easy..........;-)

[SimonS]

P mean PDIP package. So this is what you need.

[Prospekteur]

Hello

have one Question about EPE pic magnetometer. In the partslist of EPE Mag is the Ic PIC16F877-20 as component listed. Can i also use PIC16F877-20P. What does the "P" stands for???

[SimonS]

I have better resolution

[Orbit]

two software !
same sensor 200yt!
exactly the same targets 2 row and 5 impulse !

[SimonS]

Sorry for late replays. I'm not often on my computer....
Look very strange ALL programmators must do same job! There is something wrong on your side. Do you sure, that you have right fuses?

; MAGGY700.ASM 30APR04 - COPYRIGHT JOHN BECKER - EPE MAGNETOMETER

;PIC16F877, 20MHz, WDT OFF, POR ON, XTAL HS

;PROGRAM WRITTEN IN TASM VARIANT - NEEDS TRANSLATING VIA TK3 TO SUIT MPASM

;Config register bits
; CP1 CP0 CP1 CP0 NIL CPD LVP BOR MCL OS2 POR WDT OS1 OS0
;  1   1   1   1   1   1   0   0   1   0   0   0   1   0
;N.B. Logic 1/0 do NOT necessarily mean that the function is On/Off
;respectively - refer to PIC16F877 data sheet

[lazzy]

SimonS

The problem is both in the programming of the PICs but also on the board (tracks and components).

The problems I described in my original post occured with a couple of pics programmed with Microchip Pickit3

However, when I reprogrammed the same couple of PIC's with Velleman K8076 programmer the results were better:
* with one of the pics, all installed eeproms are seen, and all functions are ok, but no data transfer is possible
* with the other pic, all functions plus data transfer are ok, but the resulting data files are "empty" (no data)

Regarding the board, I made only one modification: I put a 10K resistor between IC6 output and IC4 pin#1 (following shansov's tip after a post back in 2012)

Generally, I see that much of the instability of the kit was due to programming and the bahaviour of the kit depends on the programming device and software.

I will continue testing the kit and let everyone know about any other findings

regards
lazzy

[SimonS]

On post write there was problem with jumper.
I sure there is problem on your PCB. Mine work fine. Can check power line, SCH, SDA? Or if it possible some hires picture of your board.

best regards
Simon

[lazzy]

SimonS

thanks for reply

I will check SCK/SDA but I dont think there is any problem - I do have jumpers under the eeproms

I agree that there is no problem with programming the PIC - the problem is on the board, either a faulty track design or lack of necessary components (such as some resistors...)

have you seen shansov's posts (#221-#223, posted in December 2012) regarding the same problem?
and his solution, putting a 10K resistor between IC6 out and IC4 pin#1, instead of the jumper?
have you tried this?

regards
lazzy