Whites Classic, II, III, ID, and IDX Modifications

[markantony]

this is most likely for low battery power. Take a picture of everything.

[Koala]

Dont recognise the 505-1009-B board.

[firebird24]

please answer some from the specialists

[firebird24]

Thanks.
But is this realy the same??
See under U9 at the pic from you and my Board. At my are more resistor

[kt315]

board with a mod

[Koala]

no idea about the mods but the original board should look like this

[firebird24]

need help please

[firebird24]

IDX MOD HELP

Hello from Germany.
I need some help with my IDX Pro
I have a German "TURBO" conversion on the Detector.
I would like to undo this to have a reasonable Mr. Bill conversion.
In the manual of the VR4 trimmer is the speech, which I do not have on this board but.
I hope you can help me with the board picture, which I have to change then.
If more pictures from the board are needed I can upload this tomorrow.

Thank you in advance for your help

and sorry for my bad english

[Koala]

I did as you suggested, Jumper R46 Changed VR1 to a 50K multi turn pot and i can confirm both my 6B bargain coils ( Bluemax 256 and a 6b 8 inch) work with plenty of adjustments left on the Pot. Granted, it was just outside on frozen ground and in snow but no unwanted beeping while swinging. I think I'm going to really like that small 8inch! Thanks for the advice.

your welcome.

I used this as my only machine for about 2 years. I found the 8" very stable but lacked depth. About 30% Down over a homemade. However I could have a faulty one.

with quality headphones it really does talk to you. Eventually by the sharpness and or length of the sound you have a good idea what you are digging.

Aluminium give a longer softer beep. Coins give a nice sharp sound and so on.

[Tibuck19]

I have tried the 6B on the silverdogs board

You run out of adjustment on the ground balance. I added a resistor in series.

But if you jumper R46 and change VR1 to 50K and it looks like it will work with both types of coil.


The adjustment will be more course but you could gain the adjustments sensitivity back by using a multi turn POT if it will fit into your housing

I did as you suggested, Jumper R46 Changed VR1 to a 50K multi turn pot and i can confirm both my 6B bargain coils ( Bluemax 256 and a 6b 8 inch) work with plenty of adjustments left on the Pot. Granted, it was just outside on frozen ground and in snow but no unwanted beeping while swinging. I think I'm going to really like that small 8inch! Thanks for the advice.

[pustareka]

DIGITALE WHITE

[keith777]

thanks for the reply koala. much appreciated it..............

[Koala]

does anyone know if these Mods can be done to the classic 1

the Classic 1 has no all metal mode. So you can't add the threshold as that part of the circuit it missing. Without the threshold it would be difficult to adjust the ground balance.

with the Classic 1,2, 3 and IDX all built on the same PCB anything that doesn't require the all metal mode will be the same.

[keith777]

does anyone know if these Mods can be done to the classic 1

[Tibuck19]

I have tried the 6B on the silverdogs board

You run out of adjustment on the ground balance. I added a resistor in series.

But if you jumper R46 and change VR1 to 50K and it looks like it will work with both types of coil.


The adjustment will be more course but you could gain the adjustments sensitivity back by using a multi turn POT if it will fit into your housing

can you tell me which is VR1 (the Ground balance is P1 on this board might be the Vr1?? ) and R46 please look at the photo of my board.