Announcement

Collapse
No announcement yet.

Bipolar PI MD with GB and DD Coil

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Interesting… The PCBs in the pictures are original boards. There were several buyers of these circuit boards from Bulgaria. Perhaps one of them offered one of their spare boards. Since it's an original set of circuit boards, I see no problem in reselling it.

    Some more original PCB sets are available for sale here:

    Comment


    • Hi,
      Additional information for the people assembling "Dual Tone Pulse Detector Rev.B":
      1. Used search DD coil haves bridge connection in female connector between pin1 and pin5. This wire bridge have to be cutted.
      2. The noise outside the buildings is lower than inside the buildings. This allows to increase amplifying of second RX stage by changing of the value of RT1 from 20K to 100K.
      3. The removing of the capacitor C6 (1uF 63V) and making of short connection instead this capacitor haves as result more clear sound with reduced opposite tone after the target's indentification.
      Last edited by Detectorist#1; 10-23-2026, 06:35 AM.

      Comment


      • Originally posted by boilcoil View Post
        Orbit was right:




        Trading in this product began...
        https://metaldetecting.eu/index.php/...cseen.html#new​
        Look colleague boilcoil​​, I bought two shipments from GeoMax​, but I’m busy with other things right now. I posted the ad in case another colleague wants them and has the time to apply them.I’m offering them at the same price I paid. What kind of "trading" are you accusing me of?

        Comment


        • Hello everyone,

          That's right, Algan was one of the buyers from Bulgaria who purchased two sets of circuit boards. I have no problem with him reselling the boards.​

          Comment


          • My mistake; I thought that active trading of the product was actually beginning.
            I apologize to Algan and Geo Max.​

            Comment


            • Hi Boilcoil,

              No problem. Anyone can create their own PCB using the published schematic. The schematic and all values ​​are absolutely correct. However, it's not entirely easy to create a good design for a well-functioning PCB, as some traces are delicate and need to be routed precisely. To be honest, we needed about five different approaches to place the components and route their signals in such a way that no noise interferes with or can occur in the circuit. The circuit is very sensitive and requires a good PCB design. A set of two boards (main board and battery board) for this project is available on eBay.​

              Comment


              • Awesome project—congrats to Detectorist#1 and Geomax! You can tell a lot of work went into this, and it’s clearly a labor of love. Thanks for sharing it with the community—great job, and good luck!

                One small request, though: the schematic in post #189 is a PNG, and the details and notes are pretty hard to make out—especially when you zoom in, the labels and fine lines get blurry/pixelated. A PDF version of the mainboard schematic would be much easier to read, since the text, component values, net names, and notes would stay sharp and be easier to zoom in on, print, or reference while building. If you could upload the mainboard schematic as a PDF, that would be awesome—and totally understand if that’s not doable. Thanks a lot!

                Comment


                • Hello everyone,

                  When viewing a PNG file on a mobile device, the resolution isn't optimal. However, this isn't due to the PNG file itself.
                  Here's a high-resolution (1200 dpi) schematic diagram as a PDF.​

                  Dual Tone Pulse Detector Rev B (28.07.2026)(1200dpi).pdf
                  Power Board with Charger Rev.D (1200dpi).pdf

                  Comment


                  • Herşey gerçekten çok güzel .Sizden ricam tüm parçaları tedarik etmem için parça listesini paylaşmanız

                    Comment


                    • Hi,

                      the bill of material (BOM) is posted in #189 on page 13.

                      Comment


                      • Originally posted by emreeeee View Post
                        Herşey gerçekten çok güzel .Sizden ricam tüm parçaları tedarik etmem için parça listesini paylaşmanız
                        Please make posts in English, thanks.

                        Comment




                        • Hey bro, is the schematic correct? I'm kind of thinking about building this design.
                          ​

                          Comment


                          • Hi mdcn,
                            Be sure, this design was developed more than year and they was manufactured many detectors with equal characteristics. Important precautions: do not make changes in the type of the DD coil and use proposed PCBs. The design of the PCB haves important influence on the right working of this high sensitive detector. Aspect the price for parts of finished detector around 500Euro (coil 200E + Stick 100E + case 40E + PCBs 20E). The labor is yours.

                            Comment


                            • Originally posted by mdcn View Post

                              Hey bro, is the schematic correct? I'm kind of thinking about building this design.
                              ​
                              Hello,

                              Yes, the schematic is correct and matches the PCB. A set of two PCBs to go with the schematics can be found on eBay.de. If you prefer to make your own PCBs, pay attention to the information about the PCB in the schematic. Some of the traces there have specific layout requirements and are very sensitive to noise.​

                              Comment


                              • Originally posted by GeoMax View Post

                                Hello,

                                Yes, the schematic is correct and matches the PCB. A set of two PCBs to go with the schematics can be found on eBay.de. If you prefer to make your own PCBs, pay attention to the information about the PCB in the schematic. Some of the traces there have specific layout requirements and are very sensitive to noise.​


                                Thanks for your reply. I'll think it over.
                                ​

                                Comment

                                Working...
                                X