Announcement
Collapse
No announcement yet.
Full m/lab SD2000 schematics
Collapse
X
-
A question about low battery cct on the sd-2000 schematic
Hi there every body,
Does any body know how the low battery CCT in SD2000 is supposed to work?
I have wired the schematic on breadborad. As +VB voltage goes lower than 5.75v LED starts lighting. But in SD2000 user manual it has been mentioned that LED must flash on low battery.
As you can see on the schematic attached, LM393 Comparator-A goes low on battery voltage over 5.75v and goes high otherwise (having in mind that output is open collector). After that, Comparator-B has its non-inverting input connected to +Vb. It seems a little weird. How is the LED going to flash (or blink)? Does any body know about the frequency of flashing of the Low battery LED or how the circuit is going to do that?
Thanks.
Leave a comment:
-
Hi Anis,
What you are looking for is Litz with 36 strands of 32 A.W.G or .2 mm making the overall 16.55 A.W.G good luck it is hard to find.
Regards, Ian.
Leave a comment:
-
Hi Ian, please can you specify the outer ID in AWG or in mm for this type of wire? it would very helpful for my search ebay.Originally posted by IBGold View PostHi Anis,
Litz made with 36 strands of 0.2 mm enamelled wire would be perfect for what you want for a Mono coil it is what I use.
Regards, Ian.
Thx
Anis
Leave a comment:
-
Hi Anis,
Litz made with 36 strands of 0.2 mm enamelled wire would be perfect for what you want for a Mono coil it is what I use.
Regards, Ian.
Leave a comment:
-
Hi Ian, thank you for coming to support me with the DIY coil,Originally posted by IBGold View PostAnis, what size coil are you looking to build the size of Litz depends on the coil size for a coil in the 250 mm range 32/.2 Litz would be around the mark for an 450 mm coil you would need Litz with around 36/.2 strands Litz with .2 mm strands seems to work the best for Minelab PI's and is what most of the commercial coils use this is of course for the TX winding's.
Hi Mick!
Regards, Ian.
Well I m looking for the 18" coil , exactly 457mm coil, (for deep big targets)
as per last attached there is a large choice for wires, please can you specify what would be the good one for this?
Best regards
Anis
Leave a comment:
-
Hi Mick,Originally posted by Mechanic View PostAnis, in N40 N50, where is gnd for each trace? The receive signal should stay very near gnd.
Also if you take a large metal tin, you should see an obvious change in the receive signal.
It is possible that you have damaged the front end fets and 4093 when the 200v circuit was not working correctly.
The srf coil frequency measurement is useless, you need to use a faster timebase.
For the coil wire, you need to search here as there is a lot of good information posted on coil wire specs for Minelab machines. I am no guru of coil building! Check posts by IBgold.
Cheers Mick
GND is the middle of each wave.
Yep, I v already bought some spares for that as precaution,
Now I think It's working, I will share N40 and N50 waves soon (now I m replaying from my phone).
I tried with some big stainless steel saucepans and it seems that there is some responses, I m not too glad with the results, it my be some errors in the audio board (need to verify wire by wire).
In parallel I started to build an extra audio amplifier for head speakers, in order to have more sound amplitude in the output.
Now I will wait till I receive the new wires, after IBGold's support.
Thx
Anis
Leave a comment:
-
Anis, what size coil are you looking to build the size of Litz depends on the coil size for a coil in the 250 mm range 32/.2 Litz would be around the mark for an 450 mm coil you would need Litz with around 36/.2 strands Litz with .2 mm strands seems to work the best for Minelab PI's and is what most of the commercial coils use this is of course for the TX winding's.
Hi Mick!
Regards, Ian.
Leave a comment:
-
Anis, in N40 N50, where is gnd for each trace? The receive signal should stay very near gnd.
Also if you take a large metal tin, you should see an obvious change in the receive signal.
It is possible that you have damaged the front end fets and 4093 when the 200v circuit was not working correctly.
The srf coil frequency measurement is useless, you need to use a faster timebase.
For the coil wire, you need to search here as there is a lot of good information posted on coil wire specs for Minelab machines. I am no guru of coil building! Check posts by IBgold.
Cheers Mick
Leave a comment:
-
Hi Mick, again thank you to drive me to the right way,Originally posted by Mechanic View PostHi Anis,
You need at least 6v to run properly otherwise the 181v won't be high enough and there are protection circuits that stop the receive fets coming on. That is why you don't hear anything before raising the voltage to 6v.
The IRF710 will need to be mounted to some sort of heatsink as it will get hot. Make sure it is insulated as the tab has 180v on it. It is normally mounted to the case on the sd2000. If your 68r resistors are getting hot then the irf710(or tlc217) isn't working correctly or the resistors current rating are too low.
The tlc271 can easily be damaged, you might need to replace it.
Also make sure your connections are correct to it, that GRND is correct and you have the link to the 2.5v reference from the power supply circuit.
For the coil srf, to measure it I just place the coil(just connected to the scope) near(just close enough to observe decent ringing amplitude) another coil connected to a detector and look at the frequency of the ringing after tx off.
A single strand coil is no good for the sd2000. It takes too long to settle to 0v
Cheers Mick
-Accidently connected pin 6 of TLC271 to GND this caused the blocking of the Fly back, now corrected the circuit is running well and I can see stable 181V in the 100/200V capacitor.
-Coil SRF, I followed your measuring method and below are my results:
-I'm now looking for new litz wire for additionnel coil below are specifications for the wire, please is this a right chois?
-Then I connected the audio board to see if sound response is working, result was:
Sound okay, but there is no change of the tone that mean that there is no coil response to metals.
Attached is screen for N40 & N50 from the front and receive.
Please do you have any advices, you and all genius team of this forum?
Cheers Anis
Leave a comment:
-
Well, for the price I think it is a good deal. The Hantek 6022 is a very popular model. Seems to work fine.
Leave a comment:
-
Hi dbanner,Originally posted by dbanner View PostAnis, I see you are using Hantek 6022be oscilloscope. How does it perform? Are you pleased with its operation? Can you state what is the timebase range?
The specs on the website do not mention this.
I am thinking of getting one of those 20mHz Hantek scopes for my PC.
Yep, it performing well, for the timebase range it s operating as follow:
1ns to 9000s, 39 Steps.
See user manual on internet " Annex A: Specification" you will find more details.
For me as beginner it's a nice gage and easy use.
Thx
Anis
Leave a comment:
-
Thanks Qiaozhi and dbanner.
So here's the spice file,just unzip it with winrar,hope it answers some of your questions.
Cheers.....Attached Files
Leave a comment:
-
Originally posted by Anis View PostHi waltr, could you please take a look on these screens schott and advice ?, I m stuck in this result.
Rgds
Anis
Anis, I see you are using Hantek 6022be oscilloscope. How does it perform? Are you pleased with its operation? Can you state what is the timebase range?
The specs on the website do not mention this.
I am thinking of getting one of those 20mHz Hantek scopes for my PC.
Leave a comment:
Leave a comment: