My Digital Pulse detector Delta Pulse 3

[tjmlena]

thanks 4 PDF DP3

[jap]

Hi volcano
thanks for en.DP3, pdf.
best time
j.

[Nicolas]

ok

this is the the file
http://www.mediafire.com/?vl56omtv6x5dmbe

thank you Volcano for this translation

[volcano]

when you click on the ''reply'' tab there is a tab on the next page called '' Go Advanced'' in this page you will find a tab called ''Manage Attachments'' click this tab, from there go to ''Add File'' and click it. next click on 'uploader'' now click on ''Browse'' and you should be able to upload you pdf from there.

ok

this is the the file

http://www.mediafire.com/?vl56omtv6x5dmbe

[erdin]

Thank you Mr erdin.
According to the translation
We have created a PDF file
But I do not know How I upload it in the forum

when you click on the ''reply'' tab there is a tab on the next page called '' Go Advanced'' in this page you will find a tab called ''Manage Attachments'' click this tab, from there go to ''Add File'' and click it. next click on 'uploader'' now click on ''Browse'' and you should be able to upload you pdf from there.

[volcano]

Thank you Mr erdin.
According to the translation
We have created a PDF file
But I do not know How I upload it in the forum

[erdin]

Hi erdin thank you.
-a Translated good work..
-U worked an important part ( translate) because it helps everyone who Wants or works in the project and i hope more when a chance.
best time
j.

Plessure Jap as you have helped me with a few questions I have had also

[jap]

Hi erdin thank you.
-a Translated good work..
-U worked an important part ( translate) because it helps everyone who Wants or works in the project and i hope more when a chance.
best time
j.

[erdin]

I may be wrong as my Turkish reading and writing is not that great, so someone can join in if they like and what i have written below presumes you have the document in front of you.

This section is for the privies version and has been taken of the website it is not part of the current PCB.

1. In the picture, the components circuled and number 1 (2n2907) should be rotated 180 degrees like in picture
2. In the picture, the component circled and number 2 (BS250) should be rotated 180 degrees like in the picture.
3. In the picture, the component circuled and numbed 3 can be replaced with transistor BC557.
4. Mosfet IRFU024 must be replaced with mosfet 2N7000
5. BT169D should be used as opposed to SCR.
6. C13 should be a Tantalum Capacitor
7. If you intend to use the charger circuit, the two red dots in the picture below must be bridged.
PAGE 3- Title: consideration when assembling NEW PCB components
(Writing in Red) The construction should be based on the diagrams provided, abiding to general rules. (Short circuits, drying of resins)

General Notes: Information regarding LCD Winstar WG12864B
Contrast resistors: 6,8K 2,2K
Large size LCD Information Winstar WG12864A
Contrast resistors: 8,2k 560R
(Pen writing on maths paper is the wiring diagram for the LCD)

Page 4
Title: checks to be made after assembly
1. Position the PCB like in the picture above
2. Ensure for the first version 2n2907 and bs250 are installed as in picture.



Page 5
3. Next the whole circuit should be checked for 12v to ensure no shot circuits. ( NOTE, IM NOT SURE IF I TRANSLATED THIS PART CORRECTLY)
4. Now ground the – probe and check to see if there is 12V battery supply like in the picture for the pin show in the picture (NOT SURE IF I TRANSLATED THIS CORRECTLY)

Page 6
5. Place you negative probe on the Gnd sine and measure all components as shown in the pictures above, they should show 5V.
6. Next make the connection like in the picture above.


Page 10
7. Ground you negative probe to the - sine and ensure all components in the pictures above show 12v.
Page 12
8. Ground your negative probe to the – sine and ensure all components shown in the pictures above show + 1.6~1.8v.
Next sentence on the same page says: all the above must be checked.

Page 13
9. Now the PIC and LCD and all other components can be constructed as in the pictures above.
10. Looking at the picture above the Grd voltage should be checked to be between +6~7,5v (NOTE MAYE HAVE TRANSLATED THIS PART WRONG)

Next sentence: If you have not encountered any problems you may now connect PIC and LCD
Page 14
11. (NOT sure what it is asking you to do here, I think it says to connect 6.2v to the D6 the 5^th pin )
12. The frequency should be measured here as show in the picture above to show 178~180HZ


Page 15
13. The frequency should be measured here like in the picture should be 178~180HZ.
14. The frequency here should be 178~180 HZ
15. The frequency measured here should be 178~180HZ
16. The frequency measured here should be 178~180hz


If you follow all of these steps you should not encounter a problem. If a problem dose arises you may look at the forum (http://www.teknolojiekibi.com/yeni/i...p?topic=3797.0) to get the necessary information.

[tjmlena]

I want to make last version DP3.

Anyone can translate this pdf: http://www.teknolojiekibi.com/forumd...%20klavuzu.pdf
to English version. TIA

tjmalena

[thunderbolt]

Thank you, Pasha.
But there is no menu.
can we use this hex file for search ?

demo firmware can detect as full version firmware, but you can't change any parameters, it can't discriminate and this is why it is not possible to use in every condition.
it is the proof that device is working.

also there is unique oscilloscope feature in full version that you can't find in any DIY detector, with OSC you can fine tune your dampening slope on GLCD screen.

regards,

[volcano]

Hi,

I attached two demo hex to my forum. First demo hex Türkish, second demo hex English.

Link: http://www.teknolojiekibi.com/yeni/i...p?topic=3797.0



videos latest version:

http://www.youtube.com/watch?v=uLPqACOPa4U&list=UUKin-9OEooBezp0X0P9HFGQ&index=1&feature=plcp

Regards.

Thank you, Pasha.
But there is no menu.
can we use this hex file for search ?

[volcano]

can someone tell me what is a hex? is it a file or program?

Hi
the hex file is a file that contains the program.

[Qiaozhi]

can someone tell me what is a hex? is it a file or program?

Try using Google, and searching for "What is a hex file?".

http://en.wikipedia.org/wiki/Intel_HEX

[erdin]

can someone tell me what is a hex? is it a file or program?