My Digital Pulse detector Delta Pulse 3

[jap]

Hi volcano
key s=SW1,2,,,SW5!!!!!
-mod on/off IN KEY!!!

-reply#199
-best time
j.

[volcano]

Hi volcano
in that case u need only pic , key s ,lcd to do test----->on/off--->lcd light
Full wishes for the success to complete
best time
j.

what means key s ?

and I do not understand the mod on/off

[jap]

Hi volcano
in that case u need only pic , key s ,lcd to do test----->on/off--->lcd light
Full wishes for the success to complete
best time
j.

[volcano]

Hi volcano
-1- Pin Open in the normal position be zero output +E= 0 shall be zero -2- when it reaches the controlling effort Pin Open be 5v from micro PIC shall be +E=+12volt on a broad.
-3- the -E =-10,6V always.
-4- THERE IS TWO MODE
mode one Pin Open =0 ----> +E=0 ,-E=-10,6V
mode two Pin Open =+5V---> +E=+12V ,-E=-10,6V
-5- Pin Open Depend on ON/OFF KEY!!!---->enter to PIC ----> out Pin Open L/H
I hope I explained the CASE.
--IF ERROR TEST PIC!!!!!!!
best time
j.

thank you Jap

So I must install all ICs and also the PIC

[jap]

Hi volcano
-1- Pin Open in the normal position be zero output +E= 0 shall be zero -2- when it reaches the controlling effort Pin Open be 5v from micro PIC shall be +E=+12volt on a broad.
-3- the -E =-10,6V always.
-4- THERE IS TWO MODE
mode one Pin Open =0 ----> +E=0 ,-E=-10,6V
mode two Pin Open =+5V---> +E=+12V ,-E=-10,6V
-5- Pin Open Depend on ON/OFF KEY!!!---->enter to PIC ----> out Pin Open L/H
I hope I explained the CASE.
--IF ERROR TEST PIC!!!!!!!
best time
j.

[volcano]

hello Mr Jap
please tell me the value of ( -E and +E )
you look at the picture

[Biogas]

Hi Biogas
Delta is Delta, is considered deeper as he accepts the development ,It is development to improve the performance of that every developer has the direction of the development.So each and every one of them will be better if you get a good coil and good components and followed the instructions carefully you will get good results and be better --- As for Pulse StarII is the Original and is considered a reference for comparison.
best time
j.

JAP mANy thanks!

[jap]

thank you very much Mr Jap
But I have another question
wish pic I will use ( 18f452 of 18f4520 )
because in the schematic there is 18f4520.
but at the part list there is 18f452.

Hi volcano
You can use in the part list PIC 18f452-I/O.
-By comparison the two pic datasheet the two same,but 18f4520 has other fun. in one pin, it work to.
-u can test by programming & test
best time
j.

[jap]

I have tried that, but it didnt work. Any other ideas?

Thank you,
Kerry

Hi eaglewings35
-read reply#180 see the video Carefully u will know the opening and closing and a scoop with every key and other function.like time 00:57 ,,so on.
-if error in sw,s connection read reply#174,,,&test.
best time
j.

[volcano]

thank you very much Mr Jap
But I have another question
wish pic I will use ( 18f452 of 18f4520 )
because in the schematic there is 18f4520.
but at the part list there is 18f452.

[eaglewings35]

I have tried that, but it didnt work. Any other ideas?

Thank you,
Kerry

Hi,

push the Escape buttom at startup.

Regards
Jürgen

[jap]

Hi Biogas
Delta is Delta, is considered deeper as he accepts the development ,It is development to improve the performance of that every developer has the direction of the development.So each and every one of them will be better if you get a good coil and good components and followed the instructions carefully you will get good results and be better --- As for Pulse StarII is the Original and is considered a reference for comparison.
best time
j.

[jap]

Hi volcano
-You can use Pin-Header-angle Connector 1--20 directly above the pcb to LCD.
best time
j.

[Miata]

I have run into some problems. I hook up everything and get ready to set it up, and.....nothing.
There is no way to power it up, no "on" switch.
Any one tell me how to turn this DP3 on?

Thanks

Hi,

push the Escape buttom at startup.

Regards
Jürgen

[eaglewings35]

I have run into some problems. I hook up everything and get ready to set it up, and.....nothing.
There is no way to power it up, no "on" switch.
Any one tell me how to turn this DP3 on?

Thanks