Simple Russian PI detector Pirat

[Watanabe]

Just build the TL072/71 version.

don't work very well... ...


...

[Watanabe]

[QUOTE = BKY1337; 231282] Lol

Damn , i printed it at the wrong side, and already etched it. lol

I need a new layout file. Can somebody give me the layout file from this three pictures: http://blog.novaeletronica.com.br/en/detector-de-metal/

I dont know how to print the pictures in the original size. I have all parts from this layout , its just a bit bigger.
Or is it the same as the other ones? [/ QUOTE]



My PCB drawing made in February / 2013......
The last two videos are mine too.
Very poor operation.
I find that without original k157ya2, it does not work......
It follows files, including PROTEUS ARES if one wants to modify.

https://drive.google.com/open?id=0B4ev_uU4TGK5dUhfbVVGZEpzWms

...

[homefire]

Just build the TL072/71 version.

[Watanabe]

Does anyone know where I can buy k157ya2 that can ship to Brazil?
(Pay with VISA International or PAYPAL)
Thank you.

[BKY1337]

I found a layout from simple pi, looks like it is the same.
Need a .lay file if possible. I will try it tomorrow.



It's from this link: http://www.thunting.com/smf/pi_desig...t21224.30.html
But i dont have an account on this site.

[homefire]

I think what is going on is you have your print set to fill page. Put setting to Print as is. The PCB will come out the correct size.

[BKY1337]

Do you have another layout with the same parts which is smaller like the other ones?

[BKY1337]

Do you mean that i should save the file at my Desktop and then right click and print?

[homefire]

Open this i and it will come out to size.

[BKY1337]

Damn , i printed it at the wrong side, and already etched it. lol

I need a new layout file. Can somebody give me the layout file from this three pictures: http://blog.novaeletronica.com.br/en/detector-de-metal/

I dont know how to print the pictures in the original size. I have all parts from this layout , its just a bit bigger.
Or is it the same as the other ones?

[homefire]

22o Ohm is damping resistor. You should be fine with it. It should be matched to your coil. Optimum could be more or less. They just plugged that in as a Starting point .. Ball Park.

[BKY1337]

Nothing arrived until now. But i got a copper clad board, and i made my first self etched PCB.
It is the version from Hammerhead. Has somebody a schematic from it? its the NE555 +L072 one , small layout.

I have the problem that i have only one 220 ohm resistor and it seems that i can not use it with this layout but im not sure.
Almost any Pirat version use this 220 ohm resistor but not this.

[BKY1337]

1 meg for my circuit? I saw that other ones using 100k plus 10k.
Yes i need to use used 1 Watt resistors because i have only 1/4 Watt in every size.

I tried to use 4 of them together to reach 1 watt but this doesnt seem to work.

I think i will wait till my russian ic arrives and i will make the radioskot version with the 220 ohm resistor and one pot.

Im still not sure if its good enough for a poinpointer. I have tried my cable finder tool as pinpointer today and its totally crap, i want something
stronger.

[homefire]

Just use 1/4 W resistors on every thing but the Damping. Looks like Reclaimed Parts sources. I do it all the time (Trash Technology) .

Use 1 Meg http://www.taydaelectronics.com/1m-o...urn-3362p.html

[BKY1337]

Thanks a lot, which size is the pot?
I see that i need resistors with more watt.