Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    I take back what I said about the your coil; it is still not induction-balanced, or it is connected incorrectly. It should quickly settle to 0V during turn-on.
    Next, your demod does not appear to be working. Even with an incorrect input waveform it should be responding during the sample time.
    Finally, your gain stage is railed out to -5V. Even if the demod waveform is wrong, the gain stage should consistently settle to 0V.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Show me the waveforms for TP8, U6-pin8, and U6-pin14 with no target.
    First I adjust my sampling as follow:
    Click image for larger version

Name:	5.jpg
Views:	134
Size:	115.8 KB
ID:	443988
    U6-Pin8 out :
    Click image for larger version

Name:	6.jpg
Views:	122
Size:	132.6 KB
ID:	443989
    U6-Pin14 (not any output):
    Click image for larger version

Name:	7.jpg
Views:	124
Size:	123.6 KB
ID:	443990

    Leave a comment:


  • Carl-NC
    replied
    Show me the waveforms for TP8, U6-pin8, and U6-pin14 with no target.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes. You may need to reverse the inputs depending on whether iron gives a high signal or low signal. I would use -5V for pin 4.
    Hello
    Dear Carl
    Today, i tested the LED shower (my DISC schematic is based on #567 post), but i have not any reaction for ferrous or non-ferrous on led. I think the changing is very very very low and lm393 can not show.
    But i can see increase/decrease TX pulse for ferrous/non-ferrous on scope.
    First i adjusted my sampling as follow:
    Click image for larger version  Name:	1.jpg Views:	0 Size:	132.0 KB ID:	443977
    And i checked my Demod output as follow:
    Click image for larger version  Name:	2.jpg Views:	0 Size:	133.6 KB ID:	443978
    No reaction with LED.

    Again, i changed my sampling so that my demod output is a tringle:
    Click image for larger version  Name:	3.jpg Views:	0 Size:	131.1 KB ID:	443979
    Click image for larger version  Name:	4.jpg Views:	0 Size:	133.9 KB ID:	443980
    But no result with LED.
    No matter how hard I try, my output shape doesn't get any better than this triangle.
    I am sure that my LM393 is true. My LED will turn on if i change pot (lm393).

    Leave a comment:


  • Carl-NC
    replied
    Yes. You may need to reverse the inputs depending on whether iron gives a high signal or low signal. I would use -5V for pin 4.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    The simplest solution is to place a comparator after the demod stage and have the open-collector output drive a series resistor and LED (connected to +5V).
    Thank you.
    Is that correct?
    In my schematic, ground is +VB.
    Do you think i should connect pin4 of lm393 to gnd (+VB)?
    Click image for larger version

Name:	comp2.jpg
Views:	125
Size:	259.1 KB
ID:	443931
    Last edited by h9361; 12-20-2025, 06:37 PM.

    Leave a comment:


  • Carl-NC
    replied
    The simplest solution is to place a comparator after the demod stage and have the open-collector output drive a series resistor and LED (connected to +5V).

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    It looks like you are getting decent results. Now you can add the demodulator and figure out what timing gives you a reasonable signal. After that, figure out what you need to do with it to blank the audio or use a low tone. I can't tell you how to do this because I have not done it myself.
    Thank you dear Carl for your valuable tips and supporting.
    I will find the best location for sampling.
    But for starting to real test, can you give me a primary schematic in order to adding inside the box (attached)?
    In fact, i have manually built TX+preamp+DiscDemod on a small board.
    Now, i want to play next part schematic (blanking, inside of box).
    I have a proposal, i hope you accept it. Please suggest me your initial or proposed schematic for the box but its output is a simple led for only Iron detection.
    Then, I will play it and will find the best result (best sample).
    After finding the best result , finally we (with your supporting) change its led output to 2n3904 for blanking.
    I hope you accept it, i am ready to test or to play all of your suggestion.
    Thank you.
    Click image for larger version  Name:	demod.png Views:	0 Size:	651.6 KB ID:	443891

    Leave a comment:


  • Carl-NC
    replied
    It looks like you are getting decent results. Now you can add the demodulator and figure out what timing gives you a reasonable signal. After that, figure out what you need to do with it to blank the audio or use a low tone. I can't tell you how to do this because I have not done it myself.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That looks better. No try different targets.
    For better understanding, i captured with bigger targets.

    Iron Hammer:


    Aluminum bottle


    Now, I think discrimination is clear.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That looks better. No try different targets.
    Now i tested.
    It is no target:
    Click image for larger version  Name:	notarget.jpg Views:	0 Size:	122.2 KB ID:	443882
    I captured a video from moving Nail
    https://drive.google.com/file/d/1gD3...ew?usp=sharing

    And captured second video from 1euro coin
    https://drive.google.com/file/d/1moW...ew?usp=sharing

    I have never tested such nulling coil over PI.
    Do you think such nulling is as sensitive as normal DD in PI?
    Please forgive me for my annoying.
    Is it possible help me about adding your suggestion schematic for blanking audio?
    Thank you.
    Attached Files

    Leave a comment:


  • Carl-NC
    replied
    That looks better. No try different targets.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes. You want to adjust the coil overlap until the RX signal is close to zero.
    Now, i tried, the best form is like follows
    Click image for larger version

Name:	notg.jpg
Views:	125
Size:	116.2 KB
ID:	443868

    Leave a comment:


  • Carl-NC
    replied
    Yes. You want to adjust the coil overlap until the RX signal is close to zero.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Nulling a coil for PI and IB are done the same way: when you have proper IB ther should be NO SIGNAL on the RX coil, or at least a minimized signal. Your "No Target" signal in post 551 shows a huge signal, which means the coil is not nulled. It should be very small like the first signal in Fig. 26-15.
    Thank you.
    I can not understand fig. 26-15. Is that inside of your book?

    Leave a comment:

Working...
X