Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Hello
    Dear Carl.
    Please forgive me for my questions.
    As you know, range of your TX-pulse width is 10-75us (R3). I'm going to increase the range so that be able to set it in 100us.
    I saw crossbow schematic and realized that it has only changed value of C8 from 10n to 15n. According to crossbow, we will have 100us if its frequency is set to 1000pps.
    Do you think i can reach to it with the change?
    thanks.

    Leave a comment:


  • Carl-NC
    replied
    That should work.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    As far as I can tell it looks like it will work.
    Hello
    Dear Carl.
    As you know, your main sample delay is 10 - 75 us. I want to decrease its range to 10-35.
    Do you think i can do it if i change R42 pot from 10K to 5K?
    Thanks.

    Leave a comment:


  • Carl-NC
    replied
    As far as I can tell it looks like it will work.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    As far as I can tell it looks like it will work. You will need to adjust RC values to get the right timing delays. Don't ask me what they need to be because I don't know, that's something you'll have to figure out.
    Thanks dear Carl.
    I'm going to find the RC values with tests. But before doing, i need to be sure from correctness of my schematic.

    Leave a comment:


  • Carl-NC
    replied
    As far as I can tell it looks like it will work. You will need to adjust RC values to get the right timing delays. Don't ask me what they need to be because I don't know, that's something you'll have to figure out.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    I have a request, is it possible to check the 4-sampling (attached)?
    Do you see any error?
    Thank you.
    Click image for larger version

Name:	GB-Delay.jpg
Views:	1
Size:	207.8 KB
ID:	361807

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    If you are testing indoors then get it outside. Also, you will eventually need a shielded coil.
    Thanks Dear Carl,
    What is interesting is that i tested the Non-VCO version at a place and with a coil, and it was very very stable (actually i enjoyed it)!
    I just changed its audio part as VCO and i have very noise and instability at the same place and with the coil!
    Off course, my PCB is No-VCO version (Rev C2, Opt 2) and i had to build manually its VCO part (after R36) in a separated board.

    Leave a comment:


  • h9361
    replied
    Originally posted by kt315 View Post
    he uses long unshielded wires to the pots. so he gets much influences and aside noise.
    main problem of all beginners is ununderstanding of basic electronics principles.
    Thanks dear Kt315.
    Today, i ordered the shield wire and will change my wiring to POTs.

    Leave a comment:


  • kt315
    replied
    Originally posted by surfdetector View Post
    There is no instability in the VCO circuit that I built for the HH1. I built my circuit according to the schematic with no modifications. Please post some clear, high definition photographs of your PCB ( both sides) that you are working on so that we can see what it looks like.
    he uses long unshielded wires to the pots. so he gets much influences and aside noise.
    main problem of all beginners is ununderstanding of basic electronics principles.

    Leave a comment:


  • Carl-NC
    replied
    If you are testing indoors then get it outside. Also, you will eventually need a shielded coil.

    Leave a comment:


  • surfdetector
    replied
    Originally posted by h9361 View Post
    Thanks, but i have not any problem with non-motion mode! My coil without any shilding was very stable. Do you think noise is different in vco than non-vco?
    There is no instability in the VCO circuit that I built for the HH1. I built my circuit according to the schematic with no modifications. Please post some clear, high definition photographs of your PCB ( both sides) that you are working on so that we can see what it looks like.

    Leave a comment:


  • h9361
    replied
    Originally posted by kt315 View Post
    you have not to touch your coil and move it in air because it is NOT SHIELDED. i wrote that million times
    Thanks, but i have not any problem with non-motion mode! My coil without any shilding was very stable. Do you think noise is different in vco than non-vco?

    Leave a comment:


  • kt315
    replied
    you have not to touch your coil and move it in air because it is NOT SHIELDED. i wrote that million times

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    After a lot of trying, i found a 100R speaker, it works and now i can hear audio. But my audio is very unstable so that i have very bad noise when i near my hand to circuit or heatsink-Q3.
    In addition, i also have noise when i move my coil in air or up/down over ground, while i tested my circuit in non-motion mode and it was very very stable and it didn't detect any noise or ground field.
    Do you think it's normal such noise for VCO version?!

    Leave a comment:

Working...
X