Sorry, I lost track of the discussion.
h9361, you have a regular non-GB Hammerhead and then another HH with GB added to it, is that right?
It sounds like the HH+GB works fine, threshold is working and no noise as you move the coil up/down. Is that right?
It sounds like the regular HH had a threshold problem where it would not adjust to silence, but you fixed it. Correct?
Finally, after you fixed the threshold it now responds as you move the coil up & down. Does this mean you are moving the coil up & down over ground? Or motion in the air?
Announcement
Collapse
No announcement yet.
Threshold Pot doesn't work
Collapse
X
-
Dear greenOriginally posted by green View Posth9361 suggested in reply #96, I used a new PCB rev. D, now i have no noise.
Now i'm working over 4delay ground balancing (suggested by Mr. Carl.). My result is very very nice and i can work in 10us-25us with high stability over mineralization.
Don't know what the problem is. Seems to work one day, not the next.
I have built two version HH, one original Rev. D and second include GB.
Version GB is excellent and no problem.
But original HH1 has problem is THD audio, no silent.
Leave a comment:
-
h9361 suggested in reply #96, I used a new PCB rev. D, now i have no noise.Originally posted by Carl-NC View PostProbably you will need a design that has ground balancing. Hammerhead does not have that. There are several threads about ground balance designs.
Now i'm working over 4delay ground balancing (suggested by Mr. Carl.). My result is very very nice and i can work in 10us-25us with high stability over mineralization.
Don't know what the problem is. Seems to work one day, not the next.
Leave a comment:
-
Probably you will need a design that has ground balancing. Hammerhead does not have that. There are several threads about ground balance designs.
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostGlad it all worked out!
Dear Carl
As you know, my problem was that my threshold audio (pitt...pitt..) did not mute. So, according to your advise, i decreased R30 value from 150K to 50K and 100K. The problem of muting threshold audio is solved but my coil becomes unstable with up/down. Do you have any suggestion for testing?
Thanks
Leave a comment:
-
Sorry dear Carl.Originally posted by h9361 View PostI measured voltage collector of Q6 in my HH1, it is -2.5V, while my VU meter is micro range.
Similarly, i measured voltage collector of Q6 of my meter part, it's -5V.
I think i should use Ampere meter but i don't know which range is good (uA, mA or A).
I'm sure my circuit is without any mistake, i built twice and checked more and more.
I had a mistake, it works very very nice!
Thank you for your advise.
Leave a comment:
-
I measured voltage collector of Q6 in my HH1, it is -2.5V, while my VU meter is micro range.
Similarly, i measured voltage collector of Q6 of my meter part, it's -5V.
I think i should use Ampere meter but i don't know which range is good (uA, mA or A).
I'm sure my circuit is without any mistake, i built twice and checked more and more.
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostYes, that is what I was thinking.
Edit: the other side of the meter needs to be -5V, not ground.
Dear Carl
I changed R30 value and my THD problem is solved.
But i have still problem with my VU meter.
According to your advise, i built the attached circuit but i have no any reaction over meter.
Before building, i tested my VU meter, it works correctly.
I checked all of Ground (+12), -5 connections using MM and all is correct voltage.
I checked both pins of meter with MM, both voltage is -5V!!!
Leave a comment:
-
R22/C16 will have no effect on the threshold. You need to adjust R30 and/or R32.Originally posted by h9361 View Post1- I think my basic vco sound intervals is fast (pitt .. pitt...), while position of my THD Pot is at first! Do you think using R22/C16 can help?
If the wires have any looseness then impact will cause them to move and create a false signal.2- I have a pitch sound when my frame get down quickly and touch ground. Other words, i have action when my frame hits ground.
Leave a comment:
-
What is interesting is that my THD Pot can not mute the sound with 1x1m, but it can increase pitch and make a high sound.
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostYes, that is what I was thinking.
Edit: the other side of the meter needs to be -5V, not ground.
Dear Carl
Today i did a test with 1x1m coil and have faced with some problems, but its depth detection was very very nice!
1- I think my basic vco sound intervals is fast (pitt .. pitt...), while position of my THD Pot is at first! Do you think using R22/C16 can help?
2- I have a pitch sound when my frame get down quickly and touch ground. Other words, i have action when my frame hits ground.
Leave a comment:
-
Yes, that is what I was thinking.
Edit: the other side of the meter needs to be -5V, not ground.
Leave a comment:
-
Thanks dear Carl.Originally posted by Carl-NC View PostI suppose so, the collector of Q6 could drive a meter. If you want both meter & audio then add a parallel R35a, R36a, and Q6a. Adjust the R's for whatever meter you want.
Is it possible to see the attached? Is it correct ?
Leave a comment:
-
I suppose so, the collector of Q6 could drive a meter. If you want both meter & audio then add a parallel R35a, R36a, and Q6a. Adjust the R's for whatever meter you want.Originally posted by h9361 View PostIs it possible to add a meter (for exp. VU or uA meter) to HH1?!
Leave a comment:
Leave a comment: