If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Minelab uses multi-period PI to achieve iron rejection. Even then, it is only partly effective, not the same as VLF discrimination.
You are wanting to combine two completely different technologies and that will be somewhere between difficult and impossible. If you want to play with a system that is similar to what you want and already working then I suggest looking at the Voodoo project.
Dear Carl
See the attached, it's part of Off-Resonance of your Book.
I want to add the schematic beside of my HH1 but i need your help.
As you see, you mentioned the advantage of the Off-Resonance is its ferrous/non-ferrous discrimination.
Is is possible to guide me how to change the schematic so that it discriminates between ferrous/non-ferrous via two LEDs?
Please consider your off-resonance schematic in p. 37,IMD book. I want to add the two LEDs (attached) in out of IC1b (pin-7). Do you think it works for showing decreasing/increasing inductance coil?
Actually, after detecting a target by HH1, i will turn off it and turn on my Off-Resonance (your schematic) for discriminating ferrous. My main purpose of this is for nail!.
No, that's not going to work. Inductance shift is very small, in a BFO it is typically a fraction of 1%. Also, it is unlikely you can combine such a circuit with a PI transmitter.
Please read the link
Do you have any idea about GPX method for Iron rejection?
No, that's not going to work. Inductance shift is very small, in a BFO it is typically a fraction of 1%. Also, it is unlikely you can combine such a circuit with a PI transmitter.
I think he's asking whether a PI could provide ferrous discrimination by periodically switching in an inductance meter to monitor the change in coil inductance.
Hello
Yes, we can put two leds. When HH1 detected a target, we check inductance of coil, if decrease light up one LED or increase light up other LED
I don't understand. Are you asking if the inductance meter can be used to measure PI coils? If so, it should work.
I think he's asking whether a PI could provide ferrous discrimination by periodically switching in an inductance meter to monitor the change in coil inductance.
In PI, ferrous/non-ferrous discrimination can be done.
Paramagnetic materials (ferrous) increase the coil's inductance L. Diamagnetic (Copper, Silver, Gold) decrease L.
A simple inductance measurment can produce a discriminating output. For example, you can use a "test period" in which you measure the coil's inductance using a constant voltage source. You measure the time it takes for the coil to reach a test current I. This time is proportional to the inductance. Or you measure the coil's natural frequency making it oscillate. You compare it to the measurements in the absence of a target.
Hello
Dear Carl.
I hope you are fine.
I want to add a peak follower to your HH1 for controlling increase/decrease voltage of coil (ferrous/non-ferrous).
I have built your peak follower of Off-Resonance in your book (page- 37-IMD, only top channel-IC1).
Can you guide me which point of your HH1 i should connect to the peak follower as input?
Thanks
you have a regular non-GB Hammerhead and then another HH with GB added to it, is that right? Yes. It sounds like the HH+GB works fine, threshold is working and no noise as you move the coil up/down. Is that right? Yes, but i removed your audio part and added Mickstv's Audio.
It sounds like the regular HH had a threshold problem where it would not adjust to silence, but you fixed it. Corrected? Yes, silence is solved by reducing R30 from 150K t0 100K and 50K. But i have noise in coil up/down.
Finally, after you fixed the threshold it now responds as you move the coil up & down. Does this mean you are moving the coil up & down over ground? Or motion in the air? Over ground.
Leave a comment: