Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • waltr
    replied
    Originally posted by h9361 View Post
    Yes, i used an analog VU meter and works very nice.
    Now, i want to replace a digital VU meter instead of it.
    Unfortunately, i can not find a digital numeric VU. So, do you think is there a method that be able to use a regular digital voltmeter for it?
    Dear Carl, is it possible to read the explanation about disc. in PI and tell me your opinion?
    https://www.lammertbies.nl/electroni...metal-detector
    Go back and re-read the thread "my take on the HH2".
    I did add a small analog VU meter that is 'center Zero". This along with the GB method I used indicates high verse low conductive targets.
    A digital meter is not as easy to quickly see trends (just a bunch of rapidly changing numbers verse see a needle switch in one direction or the other) as a analog meter.
    Details of how to do this is in the thread.

    Leave a comment:


  • h9361
    replied
    I did the change, but i put a 100K and 1M pots for the resistor.
    Unfortunately, my voltmeter did not turn on until i changed value of the pot via rotating.
    As soon as it turns on, it shows 5V and the number did not change by passing metal over coil.

    Leave a comment:


  • Carl-NC
    replied
    Yes

    Leave a comment:


  • h9361
    replied
    Thanks for your guiding.
    Is it correct?
    Click image for larger version

Name:	5kIR.jpg
Views:	1
Size:	124.6 KB
ID:	362420

    Leave a comment:


  • Carl-NC
    replied
    Replace the VU meter with a resistor and connect the voltmeter across the resistor.
    I don't see anything new in the link. PI can only do pseudo-discrimination.

    Leave a comment:


  • h9361
    replied
    Yes, i used an analog VU meter and works very nice.
    Now, i want to replace a digital VU meter instead of it.
    Unfortunately, i can not find a digital numeric VU. So, do you think is there a method that be able to use a regular digital voltmeter for it?
    Dear Carl, is it possible to read the explanation about disc. in PI and tell me your opinion?
    Electronics project to make a metal detector based on the pulse induction principle. Use of a digital signal processor increases the detection quality.

    Leave a comment:


  • Carl-NC
    replied
    Yes, I think we have already discussed this.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl
    Please forgive me for my amatory questions.
    I want to add a Voltmeter in your HH1 so that it shows 0 number for no detecting metals. As soon as detecting, the number is increased. Do you think it's possible?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Here is an example circuit using a Colpitts. I do not guarantee this circuit will work (I think I built it many years ago) and it will certainly have some temperature drift. Technically none of these are "off-resonance" but rather something called "energy theft."

    [ATTACH]56607[/ATTACH]
    Thanks for your kindness.

    Leave a comment:


  • Carl-NC
    replied
    Here is an example circuit using a Colpitts. I do not guarantee this circuit will work (I think I built it many years ago) and it will certainly have some temperature drift. Technically none of these are "off-resonance" but rather something called "energy theft."

    Click image for larger version

Name:	EnergyTheft.gif
Views:	1
Size:	16.3 KB
ID:	362392

    Leave a comment:


  • h9361
    replied
    Thanks dear Qiaozhi.
    Please read attached, it's Off-Resonance explanation.
    As you see, it's written that we can replace Colpitts oscillator
    Actually, i want to use only a single coil. Is it possible to guide me how to change the Colpitts for the Off-Resonance?
    Thanks
    Click image for larger version

Name:	OFF-TX.jpg
Views:	1
Size:	168.6 KB
ID:	362384

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Dear Carl, i have request.
    I want to build your Off-Resonance inside of p. 37, IMD book. But i'm going to change its TX schematic with the attached (raptor TX).
    See attached,
    1- Should i use 5V or 9V?!
    2- Should i R3 with 5K pot or it's OK? (R3 should be adjusted for maximum amplitude at the collector ofQ1.)
    Thanks
    [ATTACH]56594[/ATTACH]
    That won't work.
    The original off-resonance oscillator is designed such that the bias voltage is dependent on the oscillator frequency. As a consequence, the bias voltage is also sensitive to changes in coil inductance. This is not the case with the Raptor TX.

    Leave a comment:


  • h9361
    replied
    Dear Carl, i have request.
    I want to build your Off-Resonance inside of p. 37, IMD book. But i'm going to change its TX schematic with the attached (raptor TX).
    See attached,
    1- Should i use 5V or 9V?!
    2- Should i R3 with 5K pot or it's OK? (R3 should be adjusted for maximum amplitude at the collector ofQ1.)
    Thanks
    Click image for larger version

Name:	OFF-TX.jpg
Views:	1
Size:	33.8 KB
ID:	362379

    Leave a comment:


  • h9361
    replied
    Yes, i know VLF method and its difference with PI.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Thanks.
    Please see GoldScanIV schematic.
    If understand correctly, is it trying to discriminate via different delaying?!
    [ATTACH]56593[/ATTACH]
    You have to understand that there is a big difference between rejection based on target conductivity and the way a VLF discriminates. Using target conductivity does not provide reliable ferrous discrimination.

    I think the so-called ferrous rejection in the Goldscan IV works in the same way as the TDI. That is, it hijacks the ground balance sample to create a "hole" in the target response which corresponds to the conductivity of small ferrous targets (such as nails).

    Leave a comment:

Working...
X