Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    All of the 78Lxx regulators I have seen have this pinout:

    Click image for larger version

Name:	image.png
Views:	185
Size:	115.0 KB
ID:	439319​
    You built the HHD circuit, did you have to install the 78L05 backwards?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    No changes needed.
    Thank you.
    Dear Carl, i have a technical question about 78L05 in HHD schematic. I need to learn about it.
    As you know, pine 3 is output and pine 1 is input, but you used the pines as reverse in HHD.
    Is it possible to tell me why? I am learning about it.
    Thank you.

    Leave a comment:


  • Carl-NC
    replied
    No changes needed.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    You need to ground the cable shield, plus the cable connector and the enclosure if they are metal.
    Thank you.
    I connected coil connector to ground, the problem is solved.
    Dear Carl, do you think the power part of HHD need yo any change if i use LM7805 and LM7905 instead of 78L05 and 79L05?
    Click image for larger version

Name:	Power.jpg
Views:	222
Size:	95.8 KB
ID:	439215

    Leave a comment:


  • Carl-NC
    replied
    You need to ground the cable shield, plus the cable connector and the enclosure if they are metal.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Did you attach a ground wire to the enclosure?
    No, i checked.
    But i have an external battery pack unit and i used a cable that has two wires + a shield for connecting to HHD unit.
    I think i did not connect the cable shield to ground. Do you think that is?

    Leave a comment:


  • Carl-NC
    replied
    Did you attach a ground wire to the enclosure?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    I would probably connect to the other side of R12 and then swap the positions of D4-D5 and R8. The make R8 and R12 2k.
    A better solution might be to switch the preamps to non-inverting types, then use one clamp circuit.
    Dear Carl
    I have a problem about my HHD. The unit of my PI is metallic and i touch its body or its coil connector, my PI will detect my touching.
    Do you have any idea about this problem?

    Leave a comment:


  • Carl-NC
    replied
    I would probably connect to the other side of R12 and then swap the positions of D4-D5 and R8. The make R8 and R12 2k.
    A better solution might be to switch the preamps to non-inverting types, then use one clamp circuit.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Seems like it should work unless that configuration has a minimum delay. Try changing C16 to 1n.
    Hello dear carl
    Thank you for you tip.
    Today, my micro programing for timing is finished and it is work very nice.
    I need to your help about the attached, please see the pic.
    I want to connect rx coil Simultaneously to another 5534 as input.
    As connecting as the second connection, my TP4 form will be changed, it will be like a simple pulse. Do you think the second 5534 consumes more current? Is better to add a capacitor between the two 5534…?
    Click image for larger version

Name:	IMG_20250623_111828_645.jpg
Views:	240
Size:	106.9 KB
ID:	438549

    Leave a comment:


  • Carl-NC
    replied
    Seems like it should work unless that configuration has a minimum delay. Try changing C16 to 1n.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That's a good start but everything needs to use +5V/-5V, not +12V. I have no idea about component values, it will depend on the offset at TP5 and how strong the signal is.
    Hello
    Dear Carl
    Please forgive me for my questions.
    I need your help for adjusting delay of two pulse.
    Please see attached, I want to adjust delay between S1 and S2 as 2us.
    For this, i decrease R33 from 1K to 220R, but my pulse will be disappeared. I increase the R33 from 220R so that the pulse comes back.
    I measured the minimum delay, it is 6us. Do you have any suggestion for decreasing the delay?!
    Click image for larger version

Name:	pulse.jpg
Views:	254
Size:	89.4 KB
ID:	438267

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    That's a good start but everything needs to use +5V/-5V, not +12V. I have no idea about component values, it will depend on the offset at TP5 and how strong the signal is.
    Hello Dear Carl
    I hope you are in a good health.
    Please see the attached, it is the MPS project (it is for DD coil). I used its DISC part for my HHD, it works without any problem.
    Click image for larger version

Name:	MPS 1.09.png
Views:	476
Size:	563.9 KB
ID:	438156
    As you see, the Disc part is using a separated coil for discriminating. Other words, it works like voodoo ( a mono coil for PI, a coil for Disc).
    But my problem is for DD coil. I did Mr. dfbowers​ changing to for DD coil. But as soon as doing such changing, my TP4 form will be changed as follows:
    Click image for larger version

Name:	tppp.jpg
Views:	305
Size:	24.5 KB
ID:	438157

    I changed 5534 with tl081 in Disc part, no changing. I removed the 5534 from disc pcb, my TP4 is backed!
    Do you have any suggestion for checking?
    Thanks.

    Attached Files

    Leave a comment:


  • Carl-NC
    replied
    That's a good start but everything needs to use +5V/-5V, not +12V. I have no idea about component values, it will depend on the offset at TP5 and how strong the signal is.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Probably the best place to add it is at TP5. Add another opamp stage similar to IC8b (including threshold) and have it drive an LED. You will have to figure out all the details.
    I attached a schematic, is it possible to check it and if possible, suggest me correct values for tp5?
    Thank you

    Click image for larger version

Name:	tp55.jpg
Views:	324
Size:	96.4 KB
ID:	434894

    Leave a comment:

Working...
X