Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Hello
    Dear Carl
    I hope you are passing good days.
    If you remember, you helped me to add a VU meter over my HHd (attached).
    As you know, most of VU meter is ranged 300 or 500 uV.
    I have a problem with it. As soon as receiving signal, the needle of meter always goes to endpoint.
    I think voltage range of signal is much bigger than 300 or 500uV.
    My question is, do you have any suggestion to convert output signal to 300 or 500 uV range?
    Thanks

    Click image for larger version

Name:	VU (1).jpg
Views:	2
Size:	93.5 KB
ID:	363631

    Leave a comment:


  • Carl-NC
    replied
    Originally posted by h9361 View Post
    Sorry for my questions.
    As you know, we use foil over coil with a gap.
    Do you think we still need the gap with copper-nickel plating?
    And, should i connect the plate with a wire to ground?
    Thanks
    Yes, you should always use a gap, even with a painted shield. Yes, connect the shield to the "ground" side of the coil.

    Leave a comment:


  • h9361
    replied
    Sorry for my questions.
    As you know, we use foil over coil with a gap.
    Do you think we still need the gap with copper-nickel plating?
    And, should i connect the plate with a wire to ground?
    Thanks

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    For PI you don't need a metallic shield but you do need a fairly low impedance shield. If you use carbon shield paint then use multiple thin coats. My personal preference is polyester fabric tape with copper-nickel plating, it's much easier to work with. 3M 2191FR is an example, Ali Express has cheaper options.
    Thank you dear Carl for your information.
    Unfortunately, it's not in my country.
    I searched in Ali Express, but it also is not in it.

    Leave a comment:


  • Carl-NC
    replied
    For PI you don't need a metallic shield but you do need a fairly low impedance shield. If you use carbon shield paint then use multiple thin coats. My personal preference is polyester fabric tape with copper-nickel plating, it's much easier to work with. 3M 2191FR is an example, Ali Express has cheaper options.

    Leave a comment:


  • h9361
    replied
    Originally posted by h9361 View Post
    Hello
    Dear Carl.
    I have a question about shield of PI coils.
    Some people and companies (like Minelab) insist to use Graphite powder and other prefer to use Very thin aluminum (foil).
    I tested ohm of GPX shield (graphite), it's near 200-500R, while ohm of pure metals like aluminum foil is near 1R!
    Is it possible to tell me your opinion about this?
    Thanks.
    Dear Carl
    I hope you tell me your opinion.
    Thanks.

    Leave a comment:


  • kt315
    replied
    and the depth will be better or you hope to get better protection? what is your aim?

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    I have a question about shield of PI coils.
    Some people and companies (like Minelab) insist to use Graphite powder and other prefer to use Very thin aluminum (foil).
    I tested ohm of GPX shield (graphite), it's near 200-500R, while ohm of pure metals like aluminum foil is near 1R!
    Is it possible to tell me your opinion about this?
    Thanks.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Dear Qiaozhi
    I measured Voltage TP5, is it true?
    Primary voltage (no target) = 0.140 - 0.150V

    Detecting Target:
    Minimum voltage = -5V
    Maximum voltage= +5V
    I'm not sure what you're asking.
    Have a look at the TP5 signal using an oscilloscope.

    Leave a comment:


  • h9361
    replied
    Dear Qiaozhi
    I measured Voltage TP5, is it true?
    Primary voltage (no target) = 0.140 - 0.150V

    Detecting Target:
    Minimum voltage = -5V
    Maximum voltage= +5V

    Leave a comment:


  • h9361
    replied
    Thank you Dear Walter and Qiaozhi.
    I used capacitor that resonance frequency is calculated 10KHz.
    So, it's better i build another concentric coil with different inductance.
    I saw a test video in youtube, i'm trying to use its inductance values.

    Leave a comment:


  • Qiaozhi
    replied
    As waltr said, Voodoo has no problem discriminating small ferrous targets close to the coil.

    Leave a comment:


  • waltr
    replied
    I have not done much with the VooDoo and it has been some time since I did (over a year).
    From what I remember is it did Disc ferrous verse non-ferrous on coin and nail sized objects.

    Could be the coil and/or the cap added. I had used one of the IB PI coils I built for the HH2. I did need to try various Caps to get it working.
    Re-read the book and experiment.

    Leave a comment:


  • h9361
    replied
    Is it possible for my Coil?

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Walter.
    I have a question about your experience with Voodoo project.
    I had some tests with small objects. I think it can't discriminate Small objects that is near coil (3-5cm).
    But it discriminates big object very nice.
    Had you such experience like me?
    Thanks.

    Leave a comment:

Working...
X