Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    It sounds like maybe the EFE cancellation isn't working. Make sure you have correct EFE sample pulses.

    Leave a comment:


  • MartinB
    replied
    Originally posted by h9361 View Post
    Unfortunately, it is not at my country.
    Sent you a PM

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Does you get falsing when moving the coil in air, or only close to the ground?
    Is the coil is a rigid housing or embedded in epoxy?
    I tested with/without epoxy, both of them has the problem.
    In Air and close ground has false signal.

    Leave a comment:


  • Carl-NC
    replied
    Does you get falsing when moving the coil in air, or only close to the ground?
    Is the coil is a rigid housing or embedded in epoxy?

    Leave a comment:


  • h9361
    replied
    Originally posted by MartinB View Post
    Have you tried Scotch 24 mesh. This gives a lower capacitance than copper foil.
    Unfortunately, it is not at my country.

    Leave a comment:


  • MartinB
    replied
    Originally posted by h9361 View Post
    Hello
    Dear Carl.
    Yesterday, i received the MOSFET and tested over my HHD.
    It works but has a problem. Since its current is high, i can not set frequency of my machine to 1KHz because my BAT LED will turn up.
    So, i have to decrease frequency near to 850Hz. I prefer to obey Mr. Altra's advice, using larger heat sink for IRF740/840.

    As you know, i added GB to my HHD and set its delay to 8us. I built a coil that is able to work at the delay (Teflon-AWG22-silver, it's wire of TDI Coil), i didn't used any spacer. The Coil works vey nice at the delay in a fixed state without movement so that its sensitivity is vey excellent (My TP4 form is clear). For shielding (Faraday Shielding ), i used a vey very thin copper foil, but i have a problem. Unfortunately, my machine will have action as soon as moving coil (left/right or up/down). This is only at the low delay, not at high delay.

    Do you think this is because of changing coil capacitance? Do you have any suggestion for eliminating this effect?
    I think i should use a thicker foil. Some people told me i must use only Graphite Spray!
    Do you have any suggestion?
    Thanks.
    Have you tried Scotch 24 mesh. This gives a lower capacitance than copper foil.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    I have found that the performance of MOSFET switches is difficult to gauge by the data sheet, you have to buy & try.

    There are 2 mechanisms that create power in the switch. First is the turn-on time, for that you want low RDS, especially if you are using a wide pulse width. Second is the flyback region if the MOSFET breaks down so to avoid that you want a high BVDSS. In most PI designs the avalanche is the biggest heat generator which is why I said to get a higher breakdown. But you should also pay attention to RDS, it's pretty easy to calculate what that power will be. Remember to include the coil resistance.
    Hello
    Dear Carl.
    Yesterday, i received the MOSFET and tested over my HHD.
    It works but has a problem. Since its current is high, i can not set frequency of my machine to 1KHz because my BAT LED will turn up.
    So, i have to decrease frequency near to 850Hz. I prefer to obey Mr. Altra's advice, using larger heat sink for IRF740/840.

    As you know, i added GB to my HHD and set its delay to 8us. I built a coil that is able to work at the delay (Teflon-AWG22-silver, it's wire of TDI Coil), i didn't used any spacer. The Coil works vey nice at the delay in a fixed state without movement so that its sensitivity is vey excellent (My TP4 form is clear). For shielding (Faraday Shielding ), i used a vey very thin copper foil, but i have a problem. Unfortunately, my machine will have action as soon as moving coil (left/right or up/down). This is only at the low delay, not at high delay.

    Do you think this is because of changing coil capacitance? Do you have any suggestion for eliminating this effect?
    I think i should use a thicker foil. Some people told me i must use only Graphite Spray!
    Do you have any suggestion?
    Thanks.

    Leave a comment:


  • Carl-NC
    replied
    I have found that the performance of MOSFET switches is difficult to gauge by the data sheet, you have to buy & try.

    There are 2 mechanisms that create power in the switch. First is the turn-on time, for that you want low RDS, especially if you are using a wide pulse width. Second is the flyback region if the MOSFET breaks down so to avoid that you want a high BVDSS. In most PI designs the avalanche is the biggest heat generator which is why I said to get a higher breakdown. But you should also pay attention to RDS, it's pretty easy to calculate what that power will be. Remember to include the coil resistance.

    Leave a comment:


  • Altra
    replied
    Try a larger heat sink. The FQA11N90 uses a T0-3P case which is larger than a IRF740 (T0-220 case). It may not fit your PCB.

    Leave a comment:


  • h9361
    replied
    Thank you all for your help.
    Unfortunately, heat sink gets very hot because i'm using high pulse with for my HHD+GB.
    I checked RDs of FQA11N90, it's like IRF840. I already used IRF840, it worked.
    Do you think it works if i use on my HHd?
    Thanks.

    Leave a comment:


  • Altra
    replied
    How about a heat sink?

    Leave a comment:


  • kt315
    replied
    MOSFET with a higher breakdown voltage has more Rds. that's rule.

    Leave a comment:


  • h9361
    replied
    Or the FQA11N90 ?
    It's fast swithcing, 900V-11.4A

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    If you use a MOSFET with a higher breakdown voltage (600V, 800V, etc) it will not get as hot.
    thanks.
    Do you think the K2611/2SK2611 (900V, 9A) works in HHD?

    Leave a comment:


  • Carl-NC
    replied
    If you use a MOSFET with a higher breakdown voltage (600V, 800V, etc) it will not get as hot.

    Leave a comment:

Working...
X