Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Hello
    Dear Carl
    Please see attached, i'm going to use four 18650 Lithium ion batteries for my HH1.
    As you know, voltage of HH is 12V and its ground is +VB. Is it possible to see attached and tell me whether i can the schematic for my HH or not?!
    Thanks for your kindness.
    Click image for larger version

Name:	Bat.jpg
Views:	2
Size:	112.4 KB
ID:	362437

    Leave a comment:


  • h9361
    replied
    Originally posted by waltr View Post
    Thanks for the explanation Carl. That is why it doesn't work well.
    Thanks for your complete explanation.
    Please forgive me for my questions.
    I have a question about IRF740. Unfortunately, it's rare in my country but the IRF840 is more.
    Do you think i can use IRF840 instead of it in HH?

    Leave a comment:


  • waltr
    replied
    Thanks for the explanation Carl. That is why it doesn't work well.

    Leave a comment:


  • Carl-NC
    replied
    Non-motion mode requires an opamp (IC8b) with an exceptionally low input IB spec. With SW2 open the input IB flows through the SAT cap and the offset ramps up until the opamp rails out. For a decent TL072 this is less than 0.5mV/s at the input or 50mV/s at the output. This will mess up the threshold pretty quickly. To use this for more than a few seconds you need a 1pA IB opamp.

    Leave a comment:


  • h9361
    replied
    Thanks dear Walter.
    My non-motion mode works stably for a short time (as mentioned in article ) but it's sensitivity is low and TH pot doesn't work in the mode.

    Leave a comment:


  • waltr
    replied
    Non-motion never worked for me so never used it.
    In the field motion mode is best and is not hard to use to 'pin point' a target.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl
    I have a question about motion and non-motion of HH1.
    In motion mode, TH pot works very nice and i can hear pit ... pit and its sensitivity is very good.
    But in non-motion mode (AT opened), i have a constant sound but TH pot doesn't work and i can not reach to pit ... pit.
    Other words, my HH always is in silence and its sensitivity is half than motion mode.
    I also changed R30 by different values, but nothing changed. Do you think it's normal?

    Leave a comment:


  • Carl-NC
    replied
    I don't know anything about what they are doing.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Hold the target steady over the coil where it gives a strong audio response. Adjust the pots until the voltmeter responds.
    What you are trying to do is very impractical and will be almost useless.
    OK, i will stop it.
    Dear Carl, i want to know your opinion about Lorenz method for discrimination (generate different ID for metals ), is it possible to tell me?
    Thanks.

    Leave a comment:


  • Carl-NC
    replied
    Originally posted by h9361 View Post
    I put a 5K pot and connected my Volmeter but it did not turn on.
    Hold the target steady over the coil where it gives a strong audio response. Adjust the pots until the voltmeter responds.
    What you are trying to do is very impractical and will be almost useless.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Your resistor is way too big. Try 1k-4.7k. Waltr is right, the voltmeter will be very sluggish as it does a lot of averaging. You will need to move the target slowly.
    I put a 5K pot and connected my Volmeter but it did not turn on.

    Leave a comment:


  • h9361
    replied
    Thanks dear Walter for your guiding.
    As you know, i have built two versions of HH (1-HH1-Rev-D, 2-With GB).
    Both of them works very very nice. About GB version, i changed its audio part and i added Mr. MickStv's schematic.
    According to your advise, i have to use the VU+resistor in my GB version.
    Is it possible to tell me which point of MickStv's schematic is the best for connecting to VU?
    For more understand, you can read in attached Mickstv's explanation about his schematic.
    Click image for larger version

Name:	mckexpl.jpg
Views:	1
Size:	97.0 KB
ID:	362429

    Leave a comment:


  • waltr
    replied
    Originally posted by h9361 View Post
    Thanks Dear Walter.
    Your explanation:
    Discrimination
    Another addition is a meter on the Integrator output. This helps to determine target signal strength and for pin-pointing since the integrator output is Non-motion. I used an old VU meter with 500uA full scale. It is connecting from -5V and through a 20k series resistor to the Integrator output, -5V to +5V. This sets the meter to mid-scale with no target (5V/250uA = 20k). Then it goes to the left for high conductive targets (dimes, quarters) and to the right for low conductive targets (nickels) when the GEB is adjusted for 50-150usec - see posts above on target response with GEB adjustments.

    See attached, Did I get it right?
    [ATTACH]56648[/ATTACH]

    That's it. It picks off the integrator output.
    Note the 20k is for a 500uA meter. Check or measure your meter and re-calculate the resistor value.
    Here are the notes on my schematic:
    Integrator output is +5V to -5V
    referenced to ground (+VB)
    This is 0 to 10V referenced to 5V-

    600 Ohm * 500 uA = 300 mV to move meter full scale.
    R90 forms a Voltage divider with a ratio of 0.3/10
    So 600 Ohm /(.3/10) = 20k Ohm. A19.4k Ohm resistor is
    close enough to move meter to Half scale whrn integrator outout is Zero.

    Leave a comment:


  • h9361
    replied
    Originally posted by waltr View Post
    Go back and re-read the thread "my take on the HH2".
    I did add a small analog VU meter that is 'center Zero". This along with the GB method I used indicates high verse low conductive targets.
    A digital meter is not as easy to quickly see trends (just a bunch of rapidly changing numbers verse see a needle switch in one direction or the other) as a analog meter.
    Details of how to do this is in the thread.
    Thanks Dear Walter.
    Your explanation:
    Discrimination
    Another addition is a meter on the Integrator output. This helps to determine target signal strength and for pin-pointing since the integrator output is Non-motion. I used an old VU meter with 500uA full scale. It is connecting from -5V and through a 20k series resistor to the Integrator output, -5V to +5V. This sets the meter to mid-scale with no target (5V/250uA = 20k). Then it goes to the left for high conductive targets (dimes, quarters) and to the right for low conductive targets (nickels) when the GEB is adjusted for 50-150usec - see posts above on target response with GEB adjustments.

    See attached, Did I get it right?
    Click image for larger version

Name:	5kIR.jpg
Views:	1
Size:	35.1 KB
ID:	362428

    Leave a comment:


  • Carl-NC
    replied
    Your resistor is way too big. Try 1k-4.7k. Waltr is right, the voltmeter will be very sluggish as it does a lot of averaging. You will need to move the target slowly.

    Leave a comment:

Working...
X