Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Is there an easier way to use 8R speaker for VCO?!

    Leave a comment:


  • h9361
    replied
    Since i'm using a sealed acid battery (12V-1.2A), do you think it's because of its ampere?!

    Leave a comment:


  • h9361
    replied
    I even made HH1 separately (attached), but i did not hear any audio or low growl!
    I think my problem is Q5+Q6 method. Since i connected emitter of Q5 to +12V, my BD140 gets very hot. I checked connection of Q5 and Q6 more and more, they are OK.
    What is interesting is that Mr. Walter's audio works, but it's not low growl mode and has low sensitive than TP9. Other words, i have a detection from a good distance in TP9, but Walter's audio has action from half distance than TP9.
    Click image for larger version

Name:	HH1.jpg
Views:	1
Size:	38.9 KB
ID:	361711
    Attached Files

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    I did a lot of trying, but i couldn't solve my audio problem. According to your advice, i added fixed resistors + Vol pot in series speaker but my BD140 is still hot!!!
    I tested it with 4R speaker, it made no difference. I measured DC voltage of TP9 via threshold pot, that is -0.6 to 1.2V!
    For more testing, i built Mr. Walter audio+BD140 (attached), it works but sensitivity of my audio is low (i think i should increase Gain of IC8b from 100 to 200).
    Now, i'm going to build MiniPulse audio, i hope it works (attached).
    I checked my TP9 when a target is near my coil, it clearly shows targets.
    Click image for larger version

Name:	Walter-VCO.jpg
Views:	1
Size:	59.6 KB
ID:	361708
    Click image for larger version

Name:	minipulseVCO.jpg
Views:	1
Size:	33.0 KB
ID:	361709

    Leave a comment:


  • Carl-NC
    replied
    Yes

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Sounds like IC7c might be dead. Short IC7 pins 8 & 9, that will put 0V on Q5-emitter which is what you want.
    Hello
    Dear Carl.
    Is your mean a direct connection between +12V (+VB) to Q5-emitter?

    Leave a comment:


  • Carl-NC
    replied
    Probably you want to add some series resistance to the speaker. To finish debugging the circuit you might want to replace the speaker with, say, a 1k resistor. Measure all the voltages & waveforms to ensure everything is correct.

    Also, I suspect the way you implemented Volume will be ineffective. You might try adding a series fixed resistor and a series Volume pot to the speaker. The fixed resistor sets the maximum volume. You will need to experiment to get the values you want.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Sounds like IC7c might be dead. Short IC7 pins 8 & 9, that will put 0V on Q5-emitter which is what you want.
    Thanks dear Carl.
    I shored IC7 pins 8 &9, but i have a full horn and my BD140 gets hot so that you can smell it.

    Leave a comment:


  • Carl-NC
    replied
    Originally posted by h9361 View Post
    Base of my Q6 is incorrect, it's -0.024V, instead of -0.8. I checked R50 for N7, with/without of R50, no difference in base of Q6.
    As soon as touching between of Q5 and Q6, my VCO audio is heard!
    Voltage of pin 9 of ic7-c is 2.5V.
    Sounds like IC7c might be dead. Short IC7 pins 8 & 9, that will put 0V on Q5-emitter which is what you want.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes.
    I checked R31 in TP9, it changes DC voltage of the point.
    Base of my Q6 is incorrect, it's -0.024V, instead of -0.8. I checked R50 for N7, with/without of R50, no difference in base of Q6.
    As soon as touching between of Q5 and Q6, my VCO audio is heard!
    Voltage of pin 9 of ic7-c is 2.5V.

    Leave a comment:


  • Carl-NC
    replied
    Originally posted by h9361 View Post
    Please see attached, is your mean this?
    Yes.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    1. If you vary R31 the offset voltage at TP19 should vary. If it does not, something is wrong around IC8b.

    2. The base of Q6 should be -0.8V and the emitter should be 0V. If they are not, make sure N7 is high.

    3. IC9-pin3 should have a rectangular waveform on it. If it does not, something is wrong around IC9.

    4. For more volume you probably want the speaker on the collector side of BD140, with the emitter grounded.
    Thanks dear Carl for your guiding.
    I will check and tell here.
    Please see attached, is your mean this?
    Click image for larger version

Name:	Audiovco.jpg
Views:	1
Size:	102.2 KB
ID:	361655

    Leave a comment:


  • Carl-NC
    replied
    1. If you vary R31 the offset voltage at TP19 should vary. If it does not, something is wrong around IC8b.

    2. The base of Q6 should be -0.8V and the emitter should be 0V. If they are not, make sure N7 is high.

    3. IC9-pin3 should have a rectangular waveform on it. If it does not, something is wrong around IC9.

    4. For more volume you probably want the speaker on the collector side of BD140, with the emitter grounded.

    Leave a comment:


  • waltr
    replied
    If touching the circuit makes a change then something is not right.

    I never had luck getting Carl's 555 VCO working properly. That is one reason I did the PIC12F1501 VCO on my HH2. The switch, two transistor, 555 & amp were replace with an 8-pin PIC processor and code.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Walter
    Thanks for your replying.
    As you remember, i'm trying to change audio part of HH1 (VCO) for using 8-Ohm speaker. After searching, i copied Technik of the Polones detector (see attached).
    But i have a problem, my audio is muted. What is interesting is that i touch my audio part, its audio is heard.
    I think my threshold problem was for my previous audio amplifier (LM358, i had shared in your thread before), so i decide to change my audio amplifier.
    Click image for larger version

Name:	Audiovco.jpg
Views:	1
Size:	54.7 KB
ID:	361653

    Leave a comment:

Working...
X