Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Carl-NC
    replied
    Yes, resin will reduce thermal convection and cause it to get hotter.
    Edit: unless you use a thermally conductive epoxy.
    Also be aware that some epoxies can also have a dielectric effect and may slow down the coil decay.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    IRF840 is fine. It's a little better than the IRF740.
    Thank you dear Carl.
    Unfortunately, weather condition of my city is high humidity and rainy. So i'm going to use resin for my HH PCB.
    As you know, Q3 and its damping resistor heat up during operation.
    Do you think it will not couse any problem for Q3 and the resistor if i cover them with resin?!
    For exp, Does the resin increase their heat and eventually cause them to burn?

    Leave a comment:


  • Carl-NC
    replied
    IRF840 is fine. It's a little better than the IRF740.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Post 168 is

    The maximum input voltage for a 7660A is 12V, and for a 7660 it's 10V.
    The nominal voltage of your battery pack is 14.4V.


    not about IRF. Please see again.
    Thanks.
    That was in answer to Green's post, not your's.

    Leave a comment:


  • h9361
    replied
    Originally posted by Qiaozhi View Post
    I've already pointed that out. Please see post #168.
    Post 168 is

    The maximum input voltage for a 7660A is 12V, and for a 7660 it's 10V.
    The nominal voltage of your battery pack is 14.4V.


    not about IRF. Please see again.
    Thanks.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by green View Post
    Wondering why you suggest that should work. His schematic shows ICL7660, rated 10.5V absolute maximum supply volts.
    I've already pointed that out. Please see post #168.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Yes, use the 7660A for 12V. Better yet, replace it with the LTC1144 and you can get rid of the extra 7812.
    Thank you for your supporting.
    Please forgive me for my questions.
    I have a question about IRF740. Unfortunately, it's rare in my country but the IRF840 is more.
    Do you think i can use IRF840 instead of it in HH?



    Leave a comment:


  • Carl-NC
    replied
    Yes, use the 7660A for 12V. Better yet, replace it with the LTC1144 and you can get rid of the extra 7812.

    Leave a comment:


  • green
    replied
    Originally posted by Qiaozhi View Post
    That should work ok.
    Wondering why you suggest that should work. His schematic shows ICL7660, rated 10.5V absolute maximum supply volts.

    Leave a comment:


  • h9361
    replied
    Originally posted by Qiaozhi View Post
    Middle pin of the regulator should be connected to -VB.
    Thank you dear Qiaozhi for your guidance.

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Thanks.
    For last question, do you think ground pin of regular (middle pin) should be connected to +VB or -VB?
    Middle pin of the regulator should be connected to -VB.

    Leave a comment:


  • h9361
    replied
    Originally posted by Qiaozhi View Post
    That should work ok.
    Thanks.
    For last question, do you think ground pin of regular (middle pin) should be connected to +VB or -VB?

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Thanks dear Qiaozhi.
    Please see attached, i used a 12V regular.
    Do you think it works with the regular?
    [ATTACH]56660[/ATTACH]
    That should work ok.

    Leave a comment:


  • h9361
    replied
    Thanks dear Qiaozhi.
    Please see attached, i used a 12V regular.
    Do you think it works with the regular?
    Click image for larger version

Name:	Bat.jpg
Views:	2
Size:	112.4 KB
ID:	362438

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by h9361 View Post
    Hello
    Dear Carl
    Please see attached, i'm going to use four 18650 Lithium ion batteries for my HH1.
    As you know, voltage of HH is 12V and its ground is +VB. Is it possible to see attached and tell me whether i can the schematic for my HH or not?!
    Thanks for your kindness.
    [ATTACH]56659[/ATTACH]
    The maximum input voltage for a 7660A is 12V, and for a 7660 it's 10V.
    The nominal voltage of your battery pack is 14.4V.

    Leave a comment:

Working...
X