Voodoo Main Discussion

[Altair]

I did not understand anything. which planet are you from? (a - b)³ = a³ - 3a?b + 3ab? - b³

• a³ - b³ = (a - b)( a? + ab +b?)
• a³ + b³ = (a + b)( a? - ab +b?)

"You do not really understand something unless you can explain it to your grandmother."

Albert Einstein

[ivconic]

I did not understand anything. which planet are you from? (a - b)³ = a³ - 3a?b + 3ab? - b³

• a³ - b³ = (a - b)( a? + ab +b?)
• a³ + b³ = (a + b)( a? - ab +b?)

Me too !???

[Orbit]

Crazy ����

[Qiaozhi]

:лол:Хаааа овај луд?

English?

[Orbit]

:лол:Хаааа овај луд?

[Qiaozhi]

I once discovered that a 12f1840 will quite happily run on 12v

Probably not for very long though.

[6666]

There is no advantage to be gained by increasing the PIC supply voltage to 5.5V. The nominal voltage is 5V, and the +/-10 percent tolerance is to allow for possible variations in the supply voltage. You are chasing a red herring.

I once discovered that a 12f1840 will quite happily run on 12v

[Qiaozhi]

i want to be able to increase voltage to the coils or any other chip to its max or whatever voltage i noticed that 40 pin operates at 4.5v min and 5.5 max other 40 pins are 1.5 volts to 5.5 so if that 40 pin is the limiting factor at 5.5 volts you cant do it

There is no advantage to be gained by increasing the PIC supply voltage to 5.5V. The nominal voltage is 5V, and the +/-10 percent tolerance is to allow for possible variations in the supply voltage. You are chasing a red herring.

[lamoiz]

Oh i am i decided that as soon as i saw that it did what it claims ill have a few boards some extra parts no way did i plan on just slapping lower resisters in it and let it fly i know what happens when you put to much voltage in a ic chip ive programmed thousands and been popped in the face with ic parts when aholes messed around with the power supply but from what i noticed is the 40 pin has to be in and it has the lowest voltage of all the chips at a max of 5.5 volts when all the other chips are 15 volts and they can be pushed to 22 volts so is the board limited to 5.5 volts that the 40 pin uses

I did not understand anything. which planet are you from? (a - b)³ = a³ - 3a?b + 3ab? - b³

• a³ - b³ = (a - b)( a? + ab +b?)
• a³ + b³ = (a + b)( a? - ab +b?)

[SilverSurfer17]

i found the info i was looking for and now i see how it can be done

[SilverSurfer17]

i want to be able to increase voltage to the coils or any other chip to its max or whatever voltage i noticed that 40 pin operates at 4.5v min and 5.5 max other 40 pins are 1.5 volts to 5.5 so if that 40 pin is the limiting factor at 5.5 volts you cant do it

[Qiaozhi]

Is anyone willing to provide a complete circuit diagram? I want to design a patch pcb, thank you

The circuit diagrams are in Chapter 3.
What do you intend to do with the patch PCB?

[SilverSurfer17]

Oh i am i decided that as soon as i saw that it did what it claims ill have a few boards some extra parts no way did i plan on just slapping lower resisters in it and let it fly i know what happens when you put to much voltage in a ic chip ive programmed thousands and been popped in the face with ic parts when aholes messed around with the power supply but from what i noticed is the 40 pin has to be in and it has the lowest voltage of all the chips at a max of 5.5 volts when all the other chips are 15 volts and they can be pushed to 22 volts so is the board limited to 5.5 volts that the 40 pin uses

[jeep6789]

Is anyone willing to provide a complete circuit diagram? I want to design a patch pcb, thank you

[Qiaozhi]

I would advise making the design as it currently exists first, and then perform any modifications after you get it working.