Pinpointer with discrimination "Cat-FM" on ATMega328P

[void118]

Dear friends,

here Is new, more stable firmware for this project, If you want quick reply, you can ask me In comments on my youtube channel. all comments and suggestions are welcome

https://drive.google.com/file/d/1_BS...ew?usp=sharing

Moreover, I can add any functionality you need to my project, I mean settings, vibro motor, and any you want, this Is young project and I want to make It much better.

[useus]

They will work,I've test It!

I mean that the pcb must be tested, I would not have made mistakes

[MartyJ1963]

Thank you Void118 and Useus for this project. It would be great with a Vibro Motor added. Thank you for the Pinointer project,,,I've been looking for one for a while. Regards, Marty.

[useus]

CAT FM 328P OK.rar

pcb revised and corrected, tested on breadboard
Sorry for the inconvenience

[MartyJ1963]

Are the 0.33uf electrolytic capacitors? And can I use copper enamelled wire for the coil? I only have 0.18mm and 0.25mm copper enamelled wire. Thanks, Marty.

[void118]

I mean that the pcb must be tested, I would not have made mistakes

Ouh, I mean bc547 and 557 tested

[void118]

Thank you Void118 and Useus for this project. It would be great with a Vibro Motor added. Thank you for the Pinointer project,,,I've been looking for one for a while. Regards, Marty.

You are welcome

[void118]

Are the 0.33uf electrolytic capacitors? And can I use copper enamelled wire for the coil? I only have 0.18mm and 0.25mm copper enamelled wire. Thanks, Marty.

If you mean L7805 IC capacitors It's ceramic one's, but please note that Is very urgent to use polyester or polypropylene capacitor In the coil circuit, I mean 33nF capacitor. Yes, you can use booth wires In this project but 0.25 will a little bit simple In coil making process. Another thing I can say, you can Increase the sensitivity If you will make the coil on the last quarter of the rod. For example you have 100mm rod and you making the coil on the one side with 25mm length but with more layers. The maing thing to ahieve Is 2-3mH coil Inductance and you can youse simple LS meter to test It. I've placed an appropriate link under my video.

[MartyJ1963]

@Void118, Thank you kindly for the project and instructions, much appreciated. Regards, Marty.

[void118]

You are welcome

[void118]

Thank you Void118 and Useus for this project. It would be great with a Vibro Motor added. Thank you for the Pinointer project,,,I've been looking for one for a while. Regards, Marty.

I will try to find In my components some Vibro Motors or may be I will order them from aliexpress and after few tests I will report about results.

[void118]

Friends, please note that another urgent thing Is 16mHz quartz crystall on board, because It's main frequency for this project, If you will try to run It under 8mHz board It'll not work properly and It must be the special build for 8mHz arduino boards.

[MartyJ1963]

@Void118, Thanks for the update. Regards, Marty.

[void118]

In addition a little bit about my coils



1. Choke "3R3" coil, enameled wire 0.1 mm, Inductance 2.2mH, sensitivity about 35mm for one Euro

2. Ferrite rod 80x10mm, 2 layers of 70 turns, litz wire 10x0.1, Inductance 2.4mH, sensitivity about 55mm for one Euro

3. Unknown Ferrite rod from aliexpress 50x10mm, 4 layers on half rod, enameled wire 0.3mm, Inductance 2.9mH, sensitivity about 50mm for one Euro

[MartyJ1963]

Thanks for the extra coil data and results Void188. Regards, Marty.