Announcement

Collapse
No announcement yet.

LOOKING FOR GOLDSCAN 4 Schematic.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • nejdet
    replied
    Originally posted by Op04 View Post
    Updated but still need to check further, this is my attemp for Eduardo's GS5 Lite
    I can't open the archives.

    Leave a comment:


  • Op04
    replied
    Updated but still need to check further, this is my attemp for Eduardo's GS5 Lite
    Attached Files

    Leave a comment:


  • David222
    replied
    Originally posted by eduardo1979 View Post

    Why don't you make the GS-5?
    In my opinion it is a better detector than the GS-4.
    In the past I made a LITE version of GS-5 and it worked very well.
    My LITE version has the identical time base as TDI SL.
    The VCO is very nice, because it has a CD4046.​

    https://youtube.com/shorts/2tXTbySBUD4
    Thank you.Do we need to enable the mirror option for Gerber output for pcb printing?I am confuced.You said you used a 33 cm coil,What was the wire number,inductance and resistance?I want to make it myself.Tanks

    Leave a comment:


  • tifred
    replied
    Originally posted by GeoMax View Post
    Hi,

    you can see it how you post your requests...
    You haven't read the posts, apparently. Otherwise, you wouldn't be asking about the files. Everything you're looking for is there. If you had read them, you would have found it and wouldn't need to ask.
    Hello Geo Max and hello everyone. Well...you were right, it didn't work. I'm going to start all over again.
    What is the assembly order for the module steps? I'll try to learn.​

    Leave a comment:


  • Op04
    replied
    Unverify, unchecked. GS5 lite with less cable.
    Attached Files

    Leave a comment:


  • tifred
    replied

    Thanks for your help.
    I’ll replace C2, C3, C5, and C10 with tantalum capacitors. Then I’ll finish building the circuit, and if everything works, I’ll try to learn how to use my oscilloscope to adjust VR1 and VR2 properly.

    Leave a comment:


  • GeoMax
    replied
    Originally posted by Geotech11 View Post

    Your op-amp negative feedback copper spacing—what is it?
    If the spacing is not reasonable, parasitic capacitance can form and cause oscillation.​
    Hi Geotech11,

    what spacing do you think is reasonable to avoid parasitic capacitance? 10mil, 15mil or even more?

    Leave a comment:


  • Geotech11
    replied
    Originally posted by Emersonpaz View Post
    Click image for larger version  Name:	20260308_195715.jpg Views:	11 Size:	567.4 KB ID:	445933 C2, C3, C5, and C10 are tantalum capacitors.C2, C3, C5, and C10 are tantalum capacitors.
    Your op-amp negative feedback copper spacing—what is it?
    If the spacing is not reasonable, parasitic capacitance can form and cause oscillation.​

    Leave a comment:


  • Emersonpaz
    replied
    Click image for larger version

Name:	20260308_195715.jpg
Views:	496
Size:	567.4 KB
ID:	445933 C2, C3, C5, and C10 are tantalum capacitors.C2, C3, C5, and C10 are tantalum capacitors.

    Leave a comment:


  • Emersonpaz
    replied
    Originally posted by tifred View Post

    Hello, I finally received all my components and have reached this stage of the build. Could someone help me with the adjustments for V1 through V5? Do I need an oscilloscope to set them correctly?

    Click image for larger version  Name:	IMG_20260303_193130.jpg Views:	0 Size:	577.3 KB ID:	445924​
    Initially, you can leave the trimpots in the noon position. After operation, perform fine adjustments using an oscilloscope, setting the frequency range using VR2.VR1 is the 0V adjustment for the oscilloscope probe connected to the TP pin.

    Leave a comment:


  • GeoMax
    replied
    Good luck… But I don't think it will work the way you're imagining, with people explaining how to adjust all the potentiometers. Judging by the board's appearance, it seems like you've simply populated it and are now asking how to "adjust" it. That's not the right way to do it. You have to populate and test the circuit module by module. Only proceed with the next module if it's working. An oscilloscope is absolutely essential.

    Leave a comment:


  • tifred
    replied


    Hello, I finally received all my components and have reached this stage of the build. Could someone help me with the adjustments for V1 through V5? Do I need an oscilloscope to set them correctly?

    Click image for larger version

Name:	IMG_20260303_193130.jpg
Views:	507
Size:	577.3 KB
ID:	445924​

    Leave a comment:


  • Laith
    replied
    Originally posted by GeoMax View Post
    Hi,

    you can see it how you post your requests...
    You haven't read the posts, apparently. Otherwise, you wouldn't be asking about the files. Everything you're looking for is there. If you had read them, you would have found it and wouldn't need to ask.
    I'll say it again: I've read many posts on this forum, but I have my reasons for requesting the files here in a single post. Not everyone is a Nikola Tesla; I'm like everyone else, looking for a good metal detector to build. There's no need to get angry; you could have helped.

    Leave a comment:


  • GeoMax
    replied
    Hi,

    you can see it how you post your requests...
    You haven't read the posts, apparently. Otherwise, you wouldn't be asking about the files. Everything you're looking for is there. If you had read them, you would have found it and wouldn't need to ask.

    Leave a comment:


  • Laith
    replied
    Originally posted by GeoMax View Post
    Hi Laith,

    If you are looking for GS5 files, why do you not read those forum posts? Everything and much more info is there as well. You only need to read the forum posts.
    It seems that you are the kind of person who want everything presented on a silver plate....but this will not work.
    Who tells you that i didn't read all posts why you so angry

    Leave a comment:

Working...
X