My Digital Pulse detector Delta Pulse 3

[hadi-dindar]

hi to all friends
i want to print the pcb of dp3 on board . but the size of this pcb wrong.


i cant match pins of pic with pcbs pins . plz send me correct pcb for print on board.


regards .

[DianaBlu]

Hello DIANABLU, you can I have the DP3 's PCB file, thanks

Download it HERE

[liudengyuan]

Hello DIANABLU, you can I have the DP3 's PCB file, thanks

[DianaBlu]

Hi, I have a question. My DP3 is working ok, but i don't understant the purpose of the two LEDs connected to the 4094. I have seen on a frontal posted something like "FERROUS" and "NO FERROUS", but by LEDs are always off.


Should they light when something is detected? There is something wrong with my circuit?


Thank you
Max

[liudengyuan]

Hello, help DP3 PCB file. Who can help me, my email [email protected] thank you

[liudengyuan]

Hello, DP3 can detect how far away, who do you have a video of it

[jap]

Hi again,
I see that the coil i have received in kit , has 2,4 ohm. So I have to put 5w1rj resistor, it´s right?
If is like this, I have a problem, because two cement resistors i have received are 5w2rj and i´m trying to find 5w1rj but i don´t see anywhere in web.
Can anybody say to me where can i find it?
Thank you very much.

Hi Malibu
-You can experiment :-
1- without .
2- with one .
3-with two resistances in parallel .
And see the result
****the true result that when does not display the --coil is not Connected--****
best time
j.

[Malibu]

Hi again,
I see that the coil i have received in kit , has 2,4 ohm. So I have to put 5w1rj resistor, it´s right?
If is like this, I have a problem, because two cement resistors i have received are 5w2rj and i´m trying to find 5w1rj but i don´t see anywhere in web.
Can anybody say to me where can i find it?
Thank you very much.

[jap]

hi to all! I always fail programing PIC18F452 in JDM2 programer by WINPIC, what programer that best in PIC18F...families that affordable or easy to make?

Hi Saromines Ramiel
-try to use picpgm ,will work with JDM2 programer .
best time
j.

[ta3chvv]

son düzenleme yapılmış şekli

[RS_Phil]

hi to all! I always fail programing PIC18F452 in JDM2 programer by WINPIC, what programer that best in PIC18F...families that affordable or easy to make?

[pigeon]

Hi pigeon
-U can not replace with [BU406D/BU426A/BU508A/BU807] its TR.
-BT169D its SCR.
---For assist Download datasheet of BT169D & replace it In relation to the V,A,,With Note arrange of pin K,G,A
best time
j.

**

hi jap


thank you very much

best time

P.

[Malibu]

Thank you vera much jap.

[jap]

Hi all,

a month ago or so I received the kit, and I have some doubts.
Can anyone help?

1 - I think the R43 of 49 Ohms is missing.Yet must be of 49 Ohms? Tolerance??
2 - Look at the R49 and R51. One is 5K6, but the other seems 4k7. Are be equal, 5K6?
[ATTACH]23518[/ATTACH]
3 - R52, R53, R55. I can not put this resistance in vertical, the wire is short.? Can I solder a piece of wire? Or do I buy another?

Thanks folks

Hi Malibu
1-R43=49 OHM
2-R49 =5.6k must be ,,,,, R51=5.6k ~4.7k
3-R52, R53, R55,R59,R61=10K. Yes U Can solder a piece of wire.
Full wishes for the success to complete
best time
j.

[Malibu]

Sorry.