IDX-PRO+VDI

[ampirate]

I have another question.

Can I use 0.30 (I have a large spool 1kg of this) and 0.50mm wire,
- instead of 0.15 and 0.70mm ?

I know the Turns and Inductance need to be recalculated.
But, does this seem workable ?

Thanks again !
- J.

[golfnut]

Where are your photos of you r board you made



Is the -8v label correct?

If used on idx the rails are +4 and -4

[fabio-evo]

@ fabio-evo

[ATTACH]29419[/ATTACH][ATTACH]29420[/ATTACH]

Thanks

[ampirate]

Thanks,

I am attempting to use it with Arduino, from page 24

[golfnut]

Yes they are interchangeable without adjustments


Ive seen them work well with both chips

[ampirate]

I am building a board - and I see the Silverdog version and the refined version.
I see Layouts and Schematics. I etched a refined board version, but I only see U# codes.
Can I assume that the Lmc6484 is directly interchangeable with a Lf347 (which I have access to) ?
I do not have access to Lmc6484 chips.
I see both of these chips in the Schematics.

Thanks for any help,
J.

[Schatztaucher]

@ fabio-evo

[golfnut]

put some close up images up of what you have done.

VDI units often show 45 if both inputs to are vdi getting the same signal. !! is there a chance your X and Y CHs are shorted together now. ?


Try remove your VDI and see if Det is good again. ?

[Valters]

New day, new problems...
I finished my VDI, and its works(Achtung minen), BUT all metals are on the same value 35-45.(small ferrite, large metal, silver and cola can). I disconnect VDI PCB and notice, that distrimination dont work anymore. Before that all was ok.
Have any experience or ideas?

[Valters]

Hi everyone,

Yesterday i build a VDI board, but it don`t work. LCD dont give i sign.(yes i try contrast pot RT1)
The are some measurments.
MCP1703(U4) Pin3 5,02 V
MCP602(U1) Pin8 0,77V, but i need 5V


MCP602(U1) Pin3 and Pin5 2,48V
X 4V
PIC16F88 Pin14 0,46V, but i need 5V
On LCD Pin2 are 0 V (need 5V)
Maybe someone has a idea wher is problem?

I`m sorry if borrowing some time with my foolishness, stupid beginners mistake.
I don`t undestand, that i need to connect all pins whear ^5V to 5V(MCP1703 pin3).

[Valters]

Hi everyone,

Yesterday i build a VDI board, but it don`t work. LCD dont give i sign.(yes i try contrast pot RT1)
The are some measurments.
MCP1703(U4) Pin3 5,02 V
MCP602(U1) Pin8 0,77V, but i need 5V
MCP602(U1) Pin3 and Pin5 2,48V
X 4V
PIC16F88 Pin14 0,46V, but i need 5V
On LCD Pin2 are 0 V (need 5V)
Maybe someone has a idea wher is problem?

[fabio-evo]

guys I need the pattern right for the 2 tones, you can post it? thanks

[compadre]

You have power and contrast but no comm from pic to lcd.
Check pins 4,5,6 and 11,12,13,14 especially make sure 5 is grounded.

Ok Thank you i think i kill my Pic some wires was wrong on the vdi

[fabio-evo]

@ fabio-evo

[ATTACH]29219[/ATTACH]
[ATTACH]29220[/ATTACH] you can do this......

thank you very much for the information, I have just finished two days from now I will have to 'desolder the whole,

[Schatztaucher]

@ fabio-evo




you can do this......