Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Originally posted by Carl-NC View Post
    Good point... h, remove R5 or R15 so the TX does not run, then connect the coil and see if it's still noisy.
    I removed R15 and i have stil noise!
    It seems that i have to build a new.

    Leave a comment:


  • Carl-NC
    replied
    Originally posted by green View Post
    Thinking disabling Tx might be a good place to start trouble shooting.
    Good point... h, remove R5 or R15 so the TX does not run, then connect the coil and see if it's still noisy.

    Leave a comment:


  • green
    replied
    Thinking disabling Tx might be a good place to start trouble shooting. EMI and EF only. (schematic)https://www.geotech1.com/pages/metde...rhead/HHd1.pdf Could connect Q3 gate to -VB. Where does the jumper go to enable Tx?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    He gets the same noise when using a Minelab coil.

    Besides EMI, it could be that the gain is way too high. Double check your resistor values. Make sure they are connected properly, with good solder joints. Post a pic of the board.
    I think i have to build a new PCB, but this time Rev. D version.
    Click image for larger version

Name:	front.jpg
Views:	1
Size:	628.6 KB
ID:	361909
    Click image for larger version

Name:	20210905_112829.jpg
Views:	1
Size:	576.9 KB
ID:	361910

    Leave a comment:


  • h9361
    replied
    Originally posted by Qiaozhi View Post
    I experienced this once when I accidentally connected the TX line of the detector to the shield of the coil cable, and the core to 0V.
    Also, note 0V is battery positive on the Hammerhead.
    It's either that or your coil cable is microphonic.
    Yes, i'm using microphonic cable. Now, i changed the shield of the coil cable and core pins, i have still high noise.

    Leave a comment:


  • Carl-NC
    replied
    He gets the same noise when using a Minelab coil.

    Besides EMI, it could be that the gain is way too high. Double check your resistor values. Make sure they are connected properly, with good solder joints. Post a pic of the board.

    Leave a comment:


  • Qiaozhi
    replied
    I experienced this once when I accidentally connected the TX line of the detector to the shield of the coil cable, and the core to 0V.
    Also, note 0V is battery positive on the Hammerhead.
    It's either that or your coil cable is microphonic.

    Leave a comment:


  • h9361
    replied
    I also tested with the closed sensitivity pot, i still have noise so that i have reaction with the slightest movement.
    As you know, i'm using Rev. C2 and the Q5, Q6, Q10, R41, R49 and R51 is not installed.
    Only MickstV's audio is connected to pin1 of IC8 (TP5). I even disconnected the audio and connected my voltmeter to TP4, then connected coil to HH1.
    As soon as the slightest movement, voltage of the point is increased, it's really very strange.
    All of my internal wire is shield type, i checked all of tune points and it's ok.

    Leave a comment:


  • h9361
    replied
    Now i tested it out of my city, it's again unstable with coil, even with commander coil of GPX.
    I tested my HH1 more in my place, it was very very stable.

    Leave a comment:


  • Carl-NC
    replied
    If you disconnect the coil and everything is stable then you are picking up EMI noise.

    Leave a comment:


  • h9361
    replied
    If no connect coil, i have no noise in TP4 and my audio is clear.
    If no connect coil, voltage of my TP4 is 640mV.
    AT is active, i have no noise if coil is static.
    As soon as the slightest movement, i have reaction.
    Before i tested it in this place more and more, it was very very stable.

    Leave a comment:


  • Carl-NC
    replied
    The voltage at TP5 can change if timing is changed. No, I doubt the problem is with those caps. If you see a lot of noise on TP4 then you are probably picking up a lot of EMI noise. Try disconnecting the coil and see if TP4 is still noisy.

    Leave a comment:


  • h9361
    replied
    No, it is still instability.
    I even touch or near my finger to internal coil wire that is connected to 5-pin, my HH1 detects it.
    I checked TP5 voltage, my pulse width and main delay pot change its voltage!
    As soon as connecting coil to my HH1, i have action even with the slightest movement, even in air.
    I also used GPX-5000 coil because it has shield, i again have a very very noisy action!
    I think my HH1 is not working correctly, i also checked TP4 form in O-scope, it's OK and can detect metals but it's very very instability.
    Do you think my C27, C14 and C15 has problem?

    Leave a comment:


  • Carl-NC
    replied
    An offset at TP4 should not cause instability. If you readjust TP4 to zero does it become stable?

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl
    I have a question about adjusting TP4 to zero.
    I set the point exactly to zero, but the adjusting will be changed after a short time.
    For example, i adjusted it to zero yesterday, but it's 640mV now and my HH1 is again unstable!
    I again checked my +/-5 voltage, it's OK. Do you think it's because of my bad 5534?!

    Leave a comment:

Working...
X