Announcement
Collapse
No announcement yet.
Threshold Pot doesn't work
Collapse
X
-
Thank you.Originally posted by Carl-NC View PostDoes it have a solid center conductor or stranded?
Generally, you want a coax with a stranded center conductor and a high characteristic impedance. The cable I use is custom made for the company I work for.
Do you have any suggestion (cable) for DD coil?
Leave a comment:
-
Does it have a solid center conductor or stranded?
Generally, you want a coax with a stranded center conductor and a high characteristic impedance. The cable I use is custom made for the company I work for.
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostNew thread, please. There is a Voodoo-specific forum.
Dear Carl
I hope you are in a good health.
About building Coil, i tested many cables for connecting Coil to unit. The best result was with RG59.
But as you know, the cable is not flexible. Since you have a lot of experience in this field, can you introduce me some good cables for this?
Thank you.
Leave a comment:
-
Before everything, i need to thank you for your tips and help.Originally posted by Carl View PostYes, the ground channel needs to match the target channel.
After a lot of trying, now my HHD (motion mode) works very very nice with GB and over 3.7-4.2 pps.
Now, i want to develop Voodoo project. Now, i edited its code for producing 4 delays.
Do you think i continue this on the thread or i should make a new?
- Likes 1
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostYes, the ground channel needs to match the target channel.
Dear Carl
First, thank you for your supporting and my amatory questions.
First see attached, it is my GB part schematic:
Now, see my Delay chart as follows,
TP4 and Del1 (main delay)= 8uS
Del1 and Del2 (GB delay)=4-5 uS
Del2 and Del3 (first EE)= 150uS
Del3 and Del4 (second EE)=10uS
But my GB pot is not working. The only model that it works, i increased Del3 and Del4 (both EE delay) so that Del4 went out of my time period (over next TP4 pulse).
See it, it is my Del4 (second EE) and next TP4 pulse.
All of my measurement was based on a 45cm coil (litz, i tested the coil over GPX5000 and works very nice). But my HHD-GB work very nice if i change my coil to 8cm with inductance 500uH.
Do you have any suggestion for testing and solving my GB problem?
Please forgive me for my questions.
Leave a comment:
-
HelloOriginally posted by Carl-NC View PostYes, the ground channel needs to match the target channel.
Dear Carl.
Thank you for your guidance.
After changing TAU capacitors, my main channel output (IC8-pin7) is good form.
In addition, gain of my main channel also was high and i changed to 1.
But see my ground channel form, do you think it is normal?
I measured results with a connected coil over ground (free metal)
I change my ground channel gain (GB pot), you can see its form in follow
Leave a comment:
-
Thank you.Originally posted by Carl-NC View PostR64-C21 and R49-C20 set the tau of the integrator. Try increasing C20 and C21 to 470nF (also C22,C23), your ripple should decrease but your target response speed will be slower.
I will test and share my result.
Do you think i should also increase or decrease C22 and C23 (GB channel)?
Leave a comment:
-
R64-C21 and R49-C20 set the tau of the integrator. Try increasing C20 and C21 to 470nF (also C22,C23), your ripple should decrease but your target response speed will be slower.
Leave a comment:
-
Thank you for your response.Originally posted by Carl-NC View Post
IC8 has a gain of 100 so you will need to increase the oscope sensitivity to 50mV/div to get an equivalent measurement. Did you do that? I suspect you will see the same problem and that it is just a normal integrator waveform. This means you either have too much gain in IC8 or not a high enough integration tau.
Is is possible to tell me definition of tau?
I will measure the result with 50mV/div and share here.
For another test, i will decrease gain of IC8 (value of R53).
About tau, is your mean that i should play (increase gain) with R64-R47/R49-48 (attached)?
I forgot to tell you, my frequency is 2.6KHz.
Leave a comment:
Leave a comment: