Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Originally posted by GeoMax View Post
    Hi h9361,

    I don't quite understand your last post. Perhaps you have little experience with electronics and PCB projects? It seems you're trying to start in the middle of an existing project and adapt it to your needs/project. That's the wrong approach. I would tackle your project as follows:

    1) Create a completely new schematic based on the Hammerhead circuit with your modifications using your schematic editor.
    2) Check and validate every part of your schematic before proceeding. You can post your circuit here and ask the community for advice if you're unsure about anything.
    3) Once your schematic is complete, the first thing you should do is choose the enclosure for your detector project before starting the PCB design.
    4) After selecting the enclosure, draw the outline of the PCB that will fit inside it. Pay attention to the mounting holes, the position of the controls, and ensure that all components fit on the PCB.
    5) Once steps 1 through 4 are complete, create the printed circuit board (PCB) in your PCB editor with dimensions that fit your chosen enclosure. Place the components and route the traces.
    6) After finishing routing your design, create Gerber files and send them to the PCB manufacturer in China, or etch the PCB yourself.
    7) Once your board is finished, populate it with components, test your circuit, and begin programming the microcontroller.​
    Dear GeoMax,
    For adjusting R18 in correct point, we need to connect the DMM on TP4 (HHD PCB).
    The Correct value for R18 is Zero volt in TP4.
    But problem is that you can not see a static value in TP4!
    So, you can not adjust the R18 in correct point.
    For this, you have to stop Pulse frequency and two samplings pulse (removing 555 timer and 74hc221 ICs).
    Then you must connect out of IC8 (pin1) to ground!
    In this mode, you can see a static value in TP4 and you can easily adjust R18 for 0V in TP4.
    After adjusting, you can add the ICs in his locations and remove the conection of pin1 of IC8 to ground.

    Leave a comment:


  • GeoMax
    replied
    Hi h9361,

    I don't quite understand your last post. Perhaps you have little experience with electronics and PCB projects? It seems you're trying to start in the middle of an existing project and adapt it to your needs/project. That's the wrong approach. I would tackle your project as follows:

    1) Create a completely new schematic based on the Hammerhead circuit with your modifications using your schematic editor.
    2) Check and validate every part of your schematic before proceeding. You can post your circuit here and ask the community for advice if you're unsure about anything.
    3) Once your schematic is complete, the first thing you should do is choose the enclosure for your detector project before starting the PCB design.
    4) After selecting the enclosure, draw the outline of the PCB that will fit inside it. Pay attention to the mounting holes, the position of the controls, and ensure that all components fit on the PCB.
    5) Once steps 1 through 4 are complete, create the printed circuit board (PCB) in your PCB editor with dimensions that fit your chosen enclosure. Place the components and route the traces.
    6) After finishing routing your design, create Gerber files and send them to the PCB manufacturer in China, or etch the PCB yourself.
    7) Once your board is finished, populate it with components, test your circuit, and begin programming the microcontroller.​

    Leave a comment:


  • h9361
    replied
    Originally posted by GeoMax View Post
    Hi h9361,

    Yes, you can remove it. Simply leave the circuit board unpopulated and bridge the three holes of potentiometer R23 with a wire jumper.
    Why do you want to remove the potentiometers? They are very helpful for correctly calibrating the circuit.​

    PI-Polones:
    I don't know the exact frequency. But I estimate it will be somewhere between 300 Hz and 600 Hz.
    Thanks dear GeoMax
    I want to make SMD PCB.
    As you probably know, for adjusting R18, i have to remove IC5, IC8, IC11 and IC12 and then connect pine 1 of IC8 to ground.
    In this case, i can adjust R18 based on voltage of TP4.
    Problem is on SMD model and we have a limitation. I can not remove this ICs from SMD, so i can not connect the pine 1 of IC8 to ground.

    Leave a comment:


  • GeoMax
    replied
    Hi h9361,

    Yes, you can remove it. Simply leave the circuit board unpopulated and bridge the three holes of potentiometer R23 with a wire jumper.
    Why do you want to remove the potentiometers? They are very helpful for correctly calibrating the circuit.​

    PI-Polones:
    I don't know the exact frequency. But I estimate it will be somewhere between 300 Hz and 600 Hz.

    Leave a comment:


  • h9361
    replied
    Originally posted by GeoMax View Post
    Hi h9361

    Thanks for the explanation. I didn't realize the depth difference was so significant with large coils and single sampling. Now I understand why guys from the Middle East and North Africa always rave about the PI Polones and say it "goes deep". The PI Polones is also a single-sample detector.
    Dear GeoMax
    Do you know at what frequency guys from the middle east and north Africa use Polones?

    Leave a comment:


  • h9361
    replied
    Originally posted by GeoMax View Post

    Click image for larger version  Name:	Mod.png Views:	0 Size:	99.3 KB ID:	445071​
    Thank you.
    So, do you think we can remove Offset adjustment without any problem?

    Leave a comment:


  • GeoMax
    replied
    Originally posted by h9361 View Post

    Thanks, so i will use 4066.
    Dear Carl, as you know, i am re-designing HHD using Micro.
    I want to remove R18 (offset) and R23 (trimmer). Do you have any suggestion for changing this to without trimmer?
    Click image for larger version  Name:	preaAmp.jpg Views:	0 Size:	38.2 KB ID:	445064
    Click image for larger version

Name:	Mod.png
Views:	135
Size:	99.3 KB
ID:	445071​

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    JFETs won't work well in this case, where he wants to switch in a ground but the signal is bipolar.
    Thanks, so i will use 4066.
    Dear Carl, as you know, i am re-designing HHD using Micro.
    I want to remove R18 (offset) and R23 (trimmer). Do you have any suggestion for changing this to without trimmer?
    Click image for larger version

Name:	preaAmp.jpg
Views:	177
Size:	38.2 KB
ID:	445064

    Leave a comment:


  • Xtrem
    replied
    I would use one​ REED RELAY, nothing more efficient and simpler​.No changes to the code or anything else​.

    Leave a comment:


  • Carl-NC
    replied
    JFETs won't work well in this case, where he wants to switch in a ground but the signal is bipolar.

    Leave a comment:


  • GeoMax
    replied
    Hello h9361,

    Instead of a third switch (CD4066), you could also use a FET switch like the J113. This would be easier to integrate into the circuit compared to an IC chip.​

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Probably you will need to add a third switch like this:

    Click image for larger version  Name:	image.png Views:	0 Size:	11.4 KB ID:	445048​
    Also, why are you driving each pulse with 2 pins (S1 and S11, for example)?
    Thanks.
    A friend helped me.
    I put code of target sample here.
    S0_OFF_TIME is TX.
    ALL_ON_TIME is sample width for all samples.
    //------------Code-----------
    TIM4->CCR1 = 36*200; // S1_1
    TIM2->CCR2 = 36*400; // S1_2

    TIM4->CCR1 = 36*(S1_OFF_TIME + S0_OFF_TIME ); // ON DELAY S1
    TIM2->CCR2 = 36*(ALL_ON_TIME + S1_OFF_TIME + S0_OFF_TIME ); // S1 PW​

    Leave a comment:


  • Carl-NC
    replied
    Probably you will need to add a third switch like this:

    Click image for larger version

Name:	image.png
Views:	141
Size:	11.4 KB
ID:	445048​
    Also, why are you driving each pulse with 2 pins (S1 and S11, for example)?

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    Then you have to use the pins that support PWM.
    Please forgive me, i can not understand.
    Please see, it is my micro and voltage level of both sampling is +-5.
    Can you tell me how can connect the EFE sampling to N4 (pin5 of 4066 switch) so that i can convert my HHD to single/double?
    Click image for larger version

Name:	HHDMicro.jpg
Views:	187
Size:	86.5 KB
ID:	445046

    Leave a comment:


  • Carl-NC
    replied
    Then you have to use the pins that support PWM.

    Leave a comment:

Working...
X