Announcement

Collapse
No announcement yet.

Threshold Pot doesn't work

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • h9361
    replied
    Thanks.
    Please see GoldScanIV schematic.
    If understand correctly, is it trying to discriminate via different delaying?!
    Click image for larger version

Name:	GoldscanIV.gif
Views:	8
Size:	114.7 KB
ID:	362378

    Leave a comment:


  • Carl-NC
    replied
    Minelab uses multi-period PI to achieve iron rejection. Even then, it is only partly effective, not the same as VLF discrimination.

    You are wanting to combine two completely different technologies and that will be somewhere between difficult and impossible. If you want to play with a system that is similar to what you want and already working then I suggest looking at the Voodoo project.

    Leave a comment:


  • h9361
    replied
    Dear Carl
    See the attached, it's part of Off-Resonance of your Book.
    I want to add the schematic beside of my HH1 but i need your help.
    As you see, you mentioned the advantage of the Off-Resonance is its ferrous/non-ferrous discrimination.
    Is is possible to guide me how to change the schematic so that it discriminates between ferrous/non-ferrous via two LEDs?
    Click image for larger version

Name:	off-res.jpg
Views:	1
Size:	198.8 KB
ID:	362376

    Please consider your off-resonance schematic in p. 37,IMD book. I want to add the two LEDs (attached) in out of IC1b (pin-7). Do you think it works for showing decreasing/increasing inductance coil?
    Click image for larger version

Name:	TwoLEd.jpg
Views:	1
Size:	37.5 KB
ID:	362377

    Actually, after detecting a target by HH1, i will turn off it and turn on my Off-Resonance (your schematic) for discriminating ferrous. My main purpose of this is for nail!.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    No, that's not going to work. Inductance shift is very small, in a BFO it is typically a fraction of 1%. Also, it is unlikely you can combine such a circuit with a PI transmitter.
    Please read the link
    Do you have any idea about GPX method for Iron rejection?

    Leave a comment:


  • Carl-NC
    replied
    No, that's not going to work. Inductance shift is very small, in a BFO it is typically a fraction of 1%. Also, it is unlikely you can combine such a circuit with a PI transmitter.

    Leave a comment:


  • h9361
    replied
    I think we can discriminate between ferrous and non-ferrous.

    Leave a comment:


  • h9361
    replied
    Originally posted by Qiaozhi View Post
    I think he's asking whether a PI could provide ferrous discrimination by periodically switching in an inductance meter to monitor the change in coil inductance.
    Hello
    Yes, we can put two leds. When HH1 detected a target, we check inductance of coil, if decrease light up one LED or increase light up other LED

    Leave a comment:


  • Qiaozhi
    replied
    Originally posted by Carl-NC View Post
    I don't understand. Are you asking if the inductance meter can be used to measure PI coils? If so, it should work.
    I think he's asking whether a PI could provide ferrous discrimination by periodically switching in an inductance meter to monitor the change in coil inductance.

    Leave a comment:


  • Carl-NC
    replied
    I don't understand. Are you asking if the inductance meter can be used to measure PI coils? If so, it should work.

    Leave a comment:


  • h9361
    replied
    Originally posted by Carl-NC View Post
    The peak follower is for a different type of design, not for PI.
    Thanks Dear Carl for your guidness.
    If possible, please see the link.
    Do you think it's OK for PI?

    Leave a comment:


  • Carl-NC
    replied
    The peak follower is for a different type of design, not for PI.

    Leave a comment:


  • h9361
    replied
    Mr. Teleno guide us to use following :

    In PI, ferrous/non-ferrous discrimination can be done.

    Paramagnetic materials (ferrous) increase the coil's inductance L. Diamagnetic (Copper, Silver, Gold) decrease L.

    A simple inductance measurment can produce a discriminating output. For example, you can use a "test period" in which you measure the coil's inductance using a constant voltage source. You measure the time it takes for the coil to reach a test current I. This time is proportional to the inductance. Or you measure the coil's natural frequency making it oscillate. You compare it to the measurements in the absence of a target.

    Leave a comment:


  • h9361
    replied
    Hello
    Dear Carl.
    I hope you are fine.
    I want to add a peak follower to your HH1 for controlling increase/decrease voltage of coil (ferrous/non-ferrous).
    I have built your peak follower of Off-Resonance in your book (page- 37-IMD, only top channel-IC1).
    Can you guide me which point of your HH1 i should connect to the peak follower as input?
    Thanks

    Leave a comment:


  • Carl-NC
    replied
    OK, it is probably because that HH version does not have GB. That is what GB does, it silences the ground response.

    Leave a comment:


  • h9361
    replied
    you have a regular non-GB Hammerhead and then another HH with GB added to it, is that right? Yes.
    It sounds like the HH+GB works fine, threshold is working and no noise as you move the coil up/down. Is that right? Yes, but i removed your audio part and added Mickstv's Audio.

    It sounds like the regular HH had a threshold problem where it would not adjust to silence, but you fixed it. Corrected?
    Yes, silence is solved by reducing R30 from 150K t0 100K and 50K. But i have noise in coil up/down.

    Finally, after you fixed the threshold it now responds as you move the coil up & down. Does this mean you are moving the coil up & down over ground? Or motion in the air? Over ground.






    Leave a comment:

Working...
X