Delta Pulse

[jap]

Hi pigeon
is LCD not working DATA not light,,, to,, AFTER re connection?
best time
j.

[pigeon]

Hi pigeon
two LED for discrimiation.
best time
j.
[ATTACH]21584[/ATTACH]

hi jap

the leds is not working

thank you

best time

pigeon.

[jap]

Hi Nicolas
-good work
- for Rx I placed an approximate value .
-Value of Rx varies according to the LCD used to obtain accurate results, you can replace each Rx by variable resistance value 10k and then set to the best mode and then reading the value and placed of resistance instead Equal to the same measured value.
-for hex when i have i put!
-for ic no equivalent.
best time
j.

[pigeon]

Hi pigeon
two LED for discrimiation.
best time
j.
[ATTACH]21584[/ATTACH]

hi jap

thank you

best time

pigeon.

[Nicolas]

Hi Jap

I not find the part ML 2039 in market : 500kHz, Serial Input
Programmable Sine Wave Generator

What is your advice for the equivalent

Best regards
Nicolas

[Nicolas]

Hi pigeon
-for the number of LCD--->u connection rong.
-for RX see pdf 1...ok
-for connection see pdf 2.
--connect two LED for discrimiation,its test if pic work..ok
best time
j.

Thx Jap for your help to All

I tested the Hex file his Working good and you are reason of these value for RX

I used two RX = 4.7K

Finaly I need your English version for Hex file as the first

[jap]

to finish this problem can you give me points - and + of the LEDs.

Hi pigeon
two LED for discrimiation.
best time
j.

[pigeon]

Hi pigeon
-for the number of LCD--->u connection rong.
-for RX see pdf 1...ok
-for connection see pdf 2.
--connect two LED for discrimiation,its test if pic work..ok
best time
j.

hi jap

to finish this problem can you give me points - and + of the LEDs. and the location of point P1 P2 P3 P4 P5 and P9 on the delta pulse klasik pcb.


thank you very much and sorry for the inconvenience


best time

[Naeem]

your problem is that you look on schematic and do not wish to notice there HV diode in DRAIN pin of the IRF740. this mod is being done ESPECCIALY FOR WHAT you WRITE NOW.

I know what you say.i added this diode before but result wasnt so good.I dont want explore my problem any more here.anyway thanks for your help.regards

[sakis1]

γεια σε ολους,προσπαθω να κατασκευασω τον διαχωρισμο απο το δελτα παλμο 2+
and probably have problems with the hex file.See this video and if you can help me
find a solution.

http://www.youtube.com/watch?v=a1lfDVBkMS8&feature=youtu.be

regard

>>>> if there is a file to help me my email is >>>> [email protected]

[Davor]

In terms of "energising" the targets there is not much difference between the spiky and flat top response. There are two differences though, you'll not observe any arcing in standard cables so you'll not fry your pinky in a process, but the avalanche limitation is quite noisy.

[kt315]

your problem is that you look on schematic and do not wish to notice there HV diode in DRAIN pin of the IRF740. this mod is being done ESPECCIALY FOR WHAT you WRITE NOW.

[Naeem]

additionally you will need setting a transformer in Base of the NPN like you see this decision-section in TV sets. it will give a more controlling current in the Base, because NPN is controlled be current, not by voltage like MOS-FET. or you can try Darlington type BU808DF, no need to set the transformer in this case. there are much mos-fet's besides IRF740, BTW. 2SK1120 2SK727 are 1000V, for example. 2SK1317 is 1500V.

hi kt315.
after doing these work can i reach more depth or not?
i asked this question because i see a cut off(400V) on flyback voltage on oscope.its because of irf740.

[Naeem]

Hi Naeem
Will not get a significant improvement in depth because the performance of fet best of BU and the important here is amps.***Improvement depends on the coil and design****
best time
j.

thanks jap for your help.

[jap]

lcd

Hi pigeon
-for the number of LCD--->u connection rong.
-for RX see pdf 1...ok
-for connection see pdf 2.
--connect two LED for discrimiation,its test if pic work..ok
best time
j.