TESORO GOLDEN SABRE

[paku]

Today i just want to say i have buy kit from silverdog is very dog and dog dog dog i have buy TGSL kit and IDX kit is just make me angry
when i make that farking TGSL its make many error so i stop it and try to make the IDX kit from silver dog dog dog and dog
when i finish make the farking IDX im still get many error on IDX kit from silver dog dog dog and dog
o when i check the schematic is not same on the circuit board is very like dog dog dog by theway thanks to send me the you can make money with your cheat board

[alonejax]

i want replace bc546 & bc557 in delta puls with best teransistor
any body can help me please ?
Dear Qiaozhi , i decide build pi detector Because i understand vlf detector can't detect more than pi detector
can you Introduction me a good pi detector for small & medium metal in dept example for 2-3 meter please ?
you help me very much Hitherto , thanks a lot bro..

[alonejax]

special thanks Qiaozhi
i have two questions
1) in all metal mode of tgsl , what's maximum sense in ground for example a hammer?
2) i want a good and strong Replacing for this part ; cd4538 & cd4066 & tl062 , use in delta puls
thanks again for replay..

[Qiaozhi]

ok bro
but i think we can better field coil ; isn't right?
can you help me please?
i think if we put more gap in field of coil ; coil have more power and sens more
do you agree my freind ?

If you increase the coil overlap you will upset the balance, and the phase-offset will be incorrect. This will result in the ground balance and discrimination not working properly. Coil building and balancing is a complex subject that would take a whole book to explain.

[alonejax]

ok bro
but i think we can better field coil ; isn't right?
can you help me please?
i think if we put more gap in field of coil ; coil have more power and sens more
do you agree my freind ?

[Qiaozhi]

Qiaozhi
how can i nulling coil & how i must put cap on coil?
please show with picture
thanks

All the details of how to build the TGSL design are in the link above.

[alonejax]

Qiaozhi
how can i nulling coil & how i must put cap on coil?
please show with picture
thanks

[liekwang]

?Please anyone who got the Board layout in black and white sides of the top and bottom of TGSL silverdog version

[simonbaker]

hello
please help me.
i made this tgsl and work well all metal but disk mode not work. -5v on schematic is -6.2v!
what can i do to improve that?

The voltage is normal, no problem there.

Try reading TGSL Troubleshooting threads for help troubleshooting. Requires oscilloscope and good understanding of the circuit.

-SB

[liekwang]

qiazhi

?Where can I find the Board pcb layout top and bottom-side file type JPG TGSL I built the first Board on page 1 and 4 not working always burnt resistor 22omh

[amarasha]

hello
please help me.
i made this tgsl and work well all metal but disk mode not work. -5v on schematic is -6.2v!
what can i do to improve that?

[alonejax]

Okey
Thank you bro

[Qiaozhi]

hi Qiaozhi & other friends
i have a question ;
i don't now what is best?

http://www.geotech1.com/forums/showthread.php?15710-TGSL-Complete-Details

or
ivconic schematic in page 209
please help me

Everything is in the link. That's why it's called "TGSL Complete Details".

[alonejax]

hi Qiaozhi & other friends
i have a question ;
i don't now what is best?

http://www.geotech1.com/forums/showthread.php?15710-TGSL-Complete-Details

or
ivconic schematic in page 209
please help me

[paku]

i need street help
i have make following TGSL coil Making and i just get detection 15cm in deep coin size is 23mm in my picture

this my coin size http://imageupload.co.uk/files/u8e12b6x610fk19pnrq3.jpg

what is my problem or i need use LCR meter to Test The Coil

im very tired about make the coil need true help about make the coil
i have make 15 set DD coil but Stil can not get 30cm distance scan why why why why

what tools i need what is
i have buy DD cover bulgarian housing and insert coil to the bulgarian cover still same

just detect 15cm full-length