BARACUDA-Legend-1

[mohandes]

All mi measure are with multi meter i dont have scope.A big coin detect an 30 cm.

realy!!
you can see 134 volt by multimeter??/
please tell me your coil ,how much the mkh?
excuse for my english

[bion]

an you take photos :
pin6 ne5534 and your coil(in scope please and carefule your probe in *10 when measure your coil voltage)

you measure by oscope or multi meter???

AND :
please measure coil voltage by multimeter (it should be near 2.5 to 3 volts )

If you find the coin in 25 cm your detector is good

All mi measure are with multi meter i dont have scope.A big coin detect an 30 cm.

[mohandes]

Now i have 137 v in the coil.-5.4v and +5.4v.Coil data: 4,4 ohm ,22 cm diameter and 24 rounds.I can detect a small coin at 25 cm.

an you take photos :
pin6 ne5534 and your coil(in scope please and carefule your probe in *10 when measure your coil voltage)

you measure by oscope or multi meter???

AND :
please measure coil voltage by multimeter (it should be near 2.5 to 3 volts )

If you find the coin in 25 cm your detector is good

[bion]

Now i have 137 v in the coil.-5.4v and +5.4v.Coil data: 4,4 ohm ,22 cm diameter and 24 rounds.I can detect a small coin at 25 cm.

[bion]

Now i have 137 v in the coil.-5,4v and +5,4v.Coil data-4,4 ohm,22 cm diameter 24 rounds.

[mohandes]

WHO can help me ;
i make another coil 25 cm and 480mkh and 0.7ohm.
i replace all transistor by bf256.i have problem in detection.and use irf instead of tip127.
explain more :
i have all voltages and all frequency (+5,-5v , 650 hz) JUST in my coil i have not 250 volts.
i think my problem can not in my coil and it is in equevalent parts(just transistors),do i say ok???

please tell me

edit :
without thing near the coil like this wave


when i put large ferrous like this :

[Wilson]

i have a problem with my barracuda. when swing the coil to the right beep will occur, swing to left no beep. When i change the wire beep sound at left side.

Hello pnp007 check these components in red circles. C14 and R35 can check this with the wrong value, if the values are greater than the original on the RC time will be greater and may possibly happen as you describe. Take a test, place a coin on the floor and pass the coil over it and wait for 5 seconds to return the coil on the coin again and check if the audio plays both ways, always giving a time frame to return the coil.
If the values are correct, check the PCB on both sides of R35.
Pnp007, this is my opinion I could be wrong not hurt to check.

[mohandes]

hi maikl
my problem is detection is veru bad ,the sound is very low,
when i put the autoclave (25 cm diameter and high is 20cm) ON the coil then the speaker have very low voice!!!!!!!!!!!!!!!

i think my problem in my coil and need help to make it( now i have 7 coils!!!!!!!!!!!!!!!!)
thx

[maikl]

mohandes
that's the problem? Poor detection or no detection?

[mohandes]

hi wilson
why i have not more than 140 volt in my coils???????????
i make two coil by the wire1.5mm^2(2mm diameter), one of them 380mkh and one of them 470 mkh, the res for them under 1ohm.
please help me.
i say again my out put all ok but ne5534 and voltage of coil not ok!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[bion]

[QUOTE=mohandes;177783]

I ended Baracuda. Conclusions: The TL 072 works like the LF 412. With the BF 256 (Q3) is fine, but if we put the BF245C works very bad (triple bad). With an experimental coil diameter 20cm, I can detect a € 1 coin a distance of 22 cm. The Baracuda is much more stable than the Surf PI.

hi can i see your coil and ne5534-6 waves??please



Mi coil have about 5,5 ohm.I dont have osciloscope.
i think bf256 more better than bf245c.
very good
please tell me about your coil ?mkh & ohm?

Edit lease return 180deg Bf transistor

if you have or find oscope can see 250 volt p-p in your coil.
please show me your waves.

[bion]

[QUOTE=mohandes;177783]

I ended Baracuda. Conclusions: The TL 072 works like the LF 412. With the BF 256 (Q3) is fine, but if we put the BF245C works very bad (triple bad). With an experimental coil diameter 20cm, I can detect a € 1 coin a distance of 22 cm. The Baracuda is much more stable than the Surf PI.

hi can i see your coil and ne5534-6 waves??please

Mi coil have about 5,5 ohm.I don't have osciloscope.

i think bf256 more better than bf245c.
very good
please tell me about your coil ?mkh & ohm?

Edit lease return 180deg Bf transistor

if you have or find oscope can see 250 volt p-p in your coil.
please show me your waves.

[bion]

Bion, I have trouble finding the original and also the fets BF256C here in my area, I find it strange what you said because I can detect a gold ring at 30cm distance using the BF245 I already posted a video on the forum with this test .
Hug.

Send me if you can photos with your PCB with components and your coil details about whire dimension.Theoreticli the onli diference betwin mi detector and your is the 2N2222 becouse the mine is PN2222.

[mohandes]

[QUOTE=Wilson;175387]Hello Mohandes,

hi wilson
i buy 2mm^2 wire.
26 turn in 28cm circle is ok?

[Wilson]

I dont make measurances in this points,(same coil ) with BF245c detect euro coin at 5 cm and with BF256 the distance is 22 cm.

Bion, I have trouble finding the original and also the fets BF256C here in my area, I find it strange what you said because I can detect a gold ring at 30cm distance using the BF245 I already posted a video on the forum with this test .
Hug.