Announcement

Collapse
No announcement yet.

BARACUDA-Legend-1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • kt315
    replied
    i suggest you to go in a school near you and to tell with a teacher of physics about '230 VOLTS AC', what is it, for what is it, and common achievements of a civilization
    in the Electricity.

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by kt315 View Post
    do you test out your home or inside your room? on backyard? at field faraway from your town?
    i am only test inside my room

    Leave a comment:


  • kt315
    replied
    do you test out your home or inside your room? on backyard? at field faraway from your town?

    Leave a comment:


  • Deghbar613
    replied
    thx kt315
    but i am using 12v batt

    Leave a comment:


  • kt315
    replied
    Voltages & Frequencies (Hz) Around the World - Generator Source​

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by Deghbar613 View Post

    Algeria
    I didn't understand what mean (you have big influence from 50Hz power line).

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by kt315 View Post
    you have big influence from 50Hz power line. re-tune Bara on sure 600Hz. (50 multiplay on 12)

    what is your country?
    Algeria

    Leave a comment:


  • kt315
    replied
    you have big influence from 50Hz power line. re-tune Bara on sure 600Hz. (50 multiplay on 12)

    what is your country?

    Leave a comment:


  • Deghbar613
    replied
    This U4 PIN4 do you think is ok ?

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by boilcoil View Post
    Hi Deghbar613,
    Sorry I saw your post late.
    If the pulse width and cycle length are stable, then what you show on the oscillograms is very similar to a malfunction in the input circuit (partial discharge).
    Check for problems with the damping resistor and the serial resistor and the health of the clamp diodes.
    If they are OK, it is most likely a shortening of the cable or between some turns of the coil.
    Try a different coil and cable.​

    PS:Also check the space between the incoming rails, mostly around the high-voltage rail (MOSFET drain).
    Hi boilcoil thx for reply
    i change coil but its the same problem
    i am beginner but i think the problem is from the mosfet is fake. i don't have other one to change it

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by kt315 View Post
    did you Bara on George's schematic (mod) or original?
    Hi kt315 thx for reply i am using Geotech Baracuda - REV-A

    ​
    This is a Geotech version of the popular Baracuda PI metal detector, which has been updated to correct several problems and schematic discrepancies associated with the original design.

    Leave a comment:


  • kt315
    replied
    did you Bara on George's schematic (mod) or original?

    Leave a comment:


  • boilcoil
    replied
    Hi Deghbar613,
    Sorry I saw your post late.
    If the pulse width and cycle length are stable, then what you show on the oscillograms is very similar to a malfunction in the input circuit (partial discharge).
    Check for problems with the damping resistor and the serial resistor and the health of the clamp diodes.
    If they are OK, it is most likely a shortening of the cable or between some turns of the coil.
    Try a different coil and cable.​

    PS:Also check the space between the incoming rails, mostly around the high-voltage rail (MOSFET drain).

    Leave a comment:


  • Deghbar613
    replied
    Originally posted by kt315 View Post
    put o-scope probe on output of preamp/op amp and do video again. i see you want to burn o-scope by the HV signal.
    Hi kt315 this video for U2 pin6
    about HV signal i am using X10 probe i think o-scope is safe

    Leave a comment:


  • kt315
    replied
    put o-scope probe on output of preamp/op amp and do video again. i see you want to burn o-scope by the HV signal.

    Leave a comment:

Working...
X