Hammerhead PI - Geotech Forums

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Topics	Statistics	Last Post
Sticky: No more thru-hole PCBs by Carl-NC Started by Carl-NC, 11-07-2007, 02:58 AM	24 responses 11,355 views 0 likes	Last Post by dennis from cairns 11-16-2018, 04:12 AM
Which four Knobs for HH PI? by douglas Started by douglas, 01-27-2011, 11:42 PM	3 responses 2,140 views 0 likes	Last Post by douglas 02-03-2011, 02:05 PM
Problem with R18 and offset calibration by samu Started by samu, 01-25-2011, 10:45 AM	1 response 1,787 views 0 likes	Last Post by Kevco 01-26-2011, 04:20 PM
Finished my HH1 (pics incl.) ! Some help needed by emir506 Started by emir506, 01-21-2011, 08:38 PM	4 responses 2,201 views 0 likes	Last Post by Qiaozhi 01-21-2011, 10:56 PM
Sucessful Hammerhead project (finally) by Kevco Started by Kevco, 01-07-2011, 03:59 AM	11 responses 3,136 views 0 likes	Last Post by Kevco 01-21-2011, 10:10 PM
HammerHead1 TP4 question - Help needed by emir506 Started by emir506, 01-20-2011, 11:11 AM	3 responses 1,733 views 0 likes	Last Post by emir506 01-21-2011, 01:19 PM
TP4 duration by samu Started by samu, 01-13-2011, 12:04 PM	6 responses 1,988 views 0 likes	Last Post by samu 01-14-2011, 09:41 AM
74HC221, diode trick and waveform timing? by Kevco Started by Kevco, 01-02-2011, 01:35 AM	3 responses 2,098 views 0 likes	Last Post by Qiaozhi 01-02-2011, 10:18 PM
Mr. carl, Mr. Carl HEP by Tilladude Started by Tilladude, 12-21-2010, 11:59 PM	1 response 1,556 views 0 likes	Last Post by Qiaozhi 12-22-2010, 08:23 AM
HH audio output stage? by Kevco Started by Kevco, 11-25-2010, 07:15 PM	5 responses 2,031 views 0 likes	Last Post by Qiaozhi 11-25-2010, 11:31 PM
HH ver D thru-hole board - dimensions? by Kevco Started by Kevco, 09-29-2010, 05:48 PM	16 responses 2,890 views 0 likes	Last Post by Kevco 10-04-2010, 02:10 AM
Right SMD Resistors? by solmer2 Started by solmer2, 10-01-2010, 04:02 PM	2 responses 1,587 views 0 likes	Last Post by solmer2 10-02-2010, 08:39 AM
Coil wire diameter by DreamOfMirrors Started by DreamOfMirrors, 09-13-2010, 10:53 AM	5 responses 2,476 views 0 likes	Last Post by DreamOfMirrors 09-15-2010, 01:23 PM
Clarification of the powersupply by maca404 Started by maca404, 08-27-2010, 12:16 PM	4 responses 1,392 views 0 likes	Last Post by maca404 08-27-2010, 02:39 PM
HH Rev C PTH project... by Nicko Started by Nicko, 08-20-2010, 06:34 AM	4 responses 1,610 views 0 likes	Last Post by Nicko 08-20-2010, 05:03 PM
Help with revC VCO audio by habitbraker Started by habitbraker, 08-13-2010, 11:33 AM	0 responses 1,269 views 0 likes	Last Post by habitbraker 08-13-2010, 11:33 AM
Successful HH project by habitbraker Started by habitbraker, 07-27-2010, 04:56 PM	3 responses 2,131 views 0 likes	Last Post by habitbraker 08-04-2010, 10:32 AM
Need Help Mr. Carl by Mohammed Started by Mohammed, 05-04-2010, 11:25 AM	1 response 1,534 views 0 likes	Last Post by fidamohd82 07-21-2010, 04:28 AM
ion detector whith hammerhead by rajesh Started by rajesh, 07-16-2010, 11:50 AM	2 responses 1,599 views 0 likes	Last Post by Morgan 07-18-2010, 04:33 PM
coil cable by greybeard Started by greybeard, 07-14-2010, 03:05 PM	2 responses 1,558 views 0 likes	Last Post by greybeard 07-18-2010, 09:02 AM
HHPIMD document Ver 1.5 by ColoradoGoldMan Started by ColoradoGoldMan, 07-12-2010, 02:57 AM	0 responses 1,092 views 0 likes	Last Post by ColoradoGoldMan 07-12-2010, 02:57 AM
Deep of the Hammerhead by Marry Started by Marry, 04-07-2007, 05:37 AM	10 responses 4,901 views 0 likes	Last Post by kt315 07-10-2010, 06:46 PM
HH controls? by Nc-Dirty-digger Started by Nc-Dirty-digger, 12-01-2009, 08:53 PM	12 responses 2,584 views 0 likes	Last Post by SVEN1 06-04-2010, 12:57 AM
Powerful PI or Hammer Head (how to increase power of coil?) by rajesh Started by rajesh, 08-12-2008, 10:01 AM	41 responses 9,570 views 0 likes	Last Post by gocko 04-23-2010, 07:53 PM
Please help the hammerhead by bobi Started by bobi, 03-21-2010, 12:46 AM	3 responses 1,829 views 0 likes	Last Post by Carl-NC 03-22-2010, 05:48 PM
SMT Hammerhead Parts Question by neptune769 Started by neptune769, 08-12-2005, 02:02 AM	6 responses 3,644 views 0 likes	Last Post by jtz54 03-04-2010, 12:53 AM

Previous 1 5 6 7 16 17 template Next

No topics found.

Mark This Channel Read

Working...

Announcement