felezjoo PI(the best pulse induction metal detector that I made until now)

[jladre]

My friends,I need your help!!!

I have created circuits on Breadboard,but it wasn't working


1. When the machine is startup, "coil error"show on screen.
2. After a few seconds,garbage characters running across to the screen.

Where did it all go wrong?

http://pan.baidu.com/share/link?shar...&uk=2405639680

http://pan.baidu.com/share/link?shar...&uk=2405639680

Thanks!

Be sure that your wiring connection is not loose especially the connection to coil.

[dennisgold]

thanks too much but i haven t usbasp prog. i buy too much ic and programmers and now i can t to buy more electronics components. thanks. i will tri with paralell port or rs232
regards

[lc516]

Be sure that your wiring connection is not loose especially the connection to coil.

Thanks for your guidance and help,It can operate normal!

I just haven't coil can be used,have here only 0.2 mm of enameled wire. I made a simple coil, 10 cm diameter and 40 turns(1.8 ohm).

The detector to restart again and again using the inferior coil.

I'm a bit lost !!!

[jladre]

Please try to used 0.5 to 1mm wire to have a lesser resistance. Be sure to achieve 350uH-400uH inductance. Be sure that you are using a pcb nit a breadboard..you cannot trust breadboard.

[RS_Phil]

At first, I must say that my usual replacement of LF357-NE5534 does not work at all: 6" basket coil= little scissors at 10-12cm, coin = nothing! Now, I replace it with TL081 (the only close one that I can find in My shoe-box) and: "Its a kind of magic!" - with 7" spider coil, 400uH-(regular CHANCE-PI coil) and sens 19: 25mm coin go up to 30cm!! UNBELIEVABLE! But theres "catch 21" - poor or none iron-mask (or iron reject). Probably because of no used lf357, so please, if someone use originally op-amp, does it work propperly? Regard
PS- Thank You Ivconic for advice about Atmels EEPROM.

They used LF157, LF257 as a replacement of LF357.

[sabios]

I've programmed the ATMEGA328P but when programming the fuses stop me read the chip in the program I'm using the desert icprog.

if I do not equiboco are L-fuce: F7, H-fuce: D1 and Extended fuce: FC ...

What would be the error ...

[CDI]

Which one pcb is latest and correct?

[jladre]

I've programmed the ATMEGA328P but when programming the fuses stop me read the chip in the program I'm using the desert icprog.

if I do not equiboco are L-fuce: F7, H-fuce: D1 and Extended fuce: FC ...

What would be the error ...

Be sure to attached external 20Mhz xtal to your atmega because sometime internal xtal wont work.

[jladre]

Which one pcb is latest and correct?

All are correct

[sabios]

then I have to put a 20Mhz xtal when programming with USBASP ...

I could teach you how to do it.

have another question first have to program the fuses and then record the truth Hex.

[dragomir]

Is this the latest version FelezJoo_PI_v3_05.hex.Ima any other on a new program?

[eclipse]

3.05 is the latest version

[jladre]

then I have to put a 20Mhz xtal when programming with USBASP ...

I could teach you how to do it.

have another question first have to program the fuses and then record the truth Hex.

Try to downlod the extreme burner for avr. It is very easy to used. Laod the hex then set the fuses then click write and thats all you have your new programed atmega.

[jladre]

I been go hunting last few hours in a known high mineral soil area and found out that felezjoo pi is useless in such area..setbthe detector to the lowest sensitivity, integ., speed, and highest ground and iron rejection but still the detector screaming when lay down few inches to surface.

[lc516]

[ATTACH]34469[/ATTACH]
I been go hunting last few hours in a known high mineral soil area and found out that felezjoo pi is useless in such area..setbthe detector to the lowest sensitivity, integ., speed, and highest ground and iron rejection but still the detector screaming when lay down few inches to surface.

That‘s bad news......but thanks for your sharing.

Maybe it's just a toy, and wasn't quite that good as theory!!!