Originally posted by Pompey
View Post
Announcement
Collapse
No announcement yet.
Serbian "Most Wanted"
Collapse
X
-
I think if you want better sound you need to change the square wave osc. and find a sine osc. imho.
-
I see!I read "sort" and I think that means to change itOriginally posted by Geo View PostHi pompey.
I don't say to change the value of the capacitor but to short it (to jump), so to don't exist capacitor
Regards
Also i made a mistake,I chaged C30 on my pcb,not C26 - C30 for audio frequency..
Leave a comment:
-
Hi pompey.Originally posted by Pompey View PostHi,Geo,I already tried different caps.Yes the sound become more beautiful if you put 7-8nf instead of 10.But it seems to me like the depth goes less with changing sound to high frequency.
I don't say to change the value of the capacitor but to short it (to jump), so to don't exist capacitor
Regards
Leave a comment:
-
Hi,Geo,I already tried different caps.Yes the sound become more beautiful if you put 7-8nf instead of 10.But it seems to me like the depth goes less with changing sound to high frequency.Originally posted by Geo View PostTry to sort the C26. Sound becomes more good (not 555 version)
Leave a comment:
-
Try to sort the C26. Sound becomes more good (not 555 version)Originally posted by Pompey View PostHi,Geo!Everything is OK.This pcb without 555 work as you described.My pcb work so too.I don`t like sound at all.I have finished 555 pcb but not tested yet.My friend has made pcb with 555 and he has big depths and very good sound.I think that 555 is the best variant.
Leave a comment:
-
Bluemax has Tx =540uH and Rx = 33mH.
Also Tx and Rx are not in phase.
Regards
Leave a comment:
-
Pravilna sinusoida ,ne vise slomljena .Veci domet ,stabilniji rad.Attached Files
Leave a comment:
-
sinusoida sa 22nf nije vise slomljena , veci domet i stabilnji rad .Attached Files
Leave a comment:
-
Hi GeoOriginally posted by Geo View PostFinally i found the solution but have another problem
.
I reversed the Tx signal again.... and i made a new calibration of the Phase, Geb and total phase potentiometers and now is ok.
It full rejects a piece 10cm of ferrite rod, also don't beep at iron and it is good on gold and copper.
But i lost depth!!!!!
It detects a 30mm coin at 40cm, no good depth for a 15" coil.
Yesterday when it was unstable it detected the same coin at 50+cm.....
Also it detects the soda can at 75cm compared to 1m yesterday.
Sound is worst ..... when the signal is strong it beeps OK, but when it is a medium or small then it beeps interrupted. Maybe i must replace it with the 555. Also it needed a fine tuning of the coil.
Maybe tommorrow if i will have free time
Regards
You must change the value of C9, how? I am not
sure, I think it would be good 6n8. Capacitor and
potentiometer, which are already added, in this case you should
remove.
Leave a comment:
-
Hi,Geo!Everything is OK.This pcb without 555 work as you described.My pcb work so too.I don`t like sound at all.I have finished 555 pcb but not tested yet.My friend has made pcb with 555 and he has big depths and very good sound.I think that 555 is the best variant.Originally posted by Geo View PostFinally i found the solution but have another problem
.
I reversed the Tx signal again.... and i made a new calibration of the Phase, Geb and total phase potentiometers and now is ok.
It full rejects a piece 10cm of ferrite rod, also don't beep at iron and it is good on gold and copper.
But i lost depth!!!!!
It detects a 30mm coin at 40cm, no good depth for a 15" coil.
Yesterday when it was unstable it detected the same coin at 50+cm.....
Also it detects the soda can at 75cm compared to 1m yesterday.
Sound is worst ..... when the signal is strong it beeps OK, but when it is a medium or small then it beeps interrupted. Maybe i must replace it with the 555. Also it needed a fine tuning of the coil.
Maybe tommorrow if i will have free time
Regards
Leave a comment:
Leave a comment: