Announcement

Collapse
No announcement yet.

LOOKING FOR GOLDSCAN 4 Schematic.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ivconic
    replied
    It works really nice. But I'm interested in core performance.
    Do you still have that detector?
    To show how GEB works on it.
    And when you set the GEB to some "mineralization", after that you can test and record how it detects a Roman coin or a small gold coin.
    In "Off" mode (GEB off) my GS4 also has "enormous" depths in the air on all tested targets.
    If you still have that detector; I would be grateful if you could record minute two of the mentioned test.
    ​

    Leave a comment:


  • eduardo1979
    replied
    Originally posted by ivconic View Post
    Last thing I done (was lazy to record another video) is to make 25cm coil, 0.3mH / 0.9R.
    In All Metal mode with GEB slightly lose; it improved air "depths" to ~15cm on small Roman coin as well as on gold coin.
    Not good enough.
    Some other works in progress...
    Why don't you make the GS-5?
    In my opinion it is a better detector than the GS-4.
    In the past I made a LITE version of GS-5 and it worked very well.
    My LITE version has the identical time base as TDI SL.
    The VCO is very nice, because it has a CD4046.​

    Attached Files

    Leave a comment:


  • ivconic
    replied
    Last thing I done (was lazy to record another video) is to make 25cm coil, 0.3mH / 0.9R.
    In All Metal mode with GEB slightly lose; it improved air "depths" to ~15cm on small Roman coin as well as on gold coin.
    Not good enough.
    Some other works in progress...

    Leave a comment:


  • ivconic
    replied
    Originally posted by kadir6141 View Post
    Hello, there is a black part on the gs4 commutator. Is this resistance? Can anyone with knowledge help? thanks.
    Probably a resistor.
    I assume it is R52 (22k) GND resistor.

    Leave a comment:


  • kadir6141
    replied
    Hello, there is a black part on the gs4 commutator. Is this resistance? Can anyone with knowledge help? thanks.

    Leave a comment:


  • YIVANKA
    replied
    Originally posted by ZOUjiarui View Post
    People always like to release pcb without inspection
    Should others deliver food to your mouth?

    Leave a comment:


  • ivconic
    replied
    Yes, made by Jose.
    Good "depths".
    I would be quite satisfied if I manage something like that.

    Leave a comment:


  • GeoMax
    replied
    Here is another video about the GS4. I think the performance is quite remarkable. The video is already 10 years old.

    Leave a comment:


  • ivconic
    replied
    Originally posted by ZOUjiarui View Post

    Will Pulsar II work as well as GoldScan on highly mineralized soils?
    With larger coil, say 60cm and above, since it is deep enough; with coil at 30cm over the soil surface; will work just fine.
    It has no GEB, so it will be affected by mineralization if coil is lowered to ground.
    But then again, with large coil 30cm up from soil surface; you search for deep and large targets and not small items.
    Large targets will give noticeable continuous audio response... so no problem in most of the cases.
    Larger the coil and larger the target = you can lift coil more from soil surface.
    You gain two benefits from that; detector will ignore small iron junk in surface and mineralization will not have significant impact on detectors behavior.

    Leave a comment:


  • ZOUjiarui
    replied
    Originally posted by ivconic View Post
    You haven't read my posts carefully (if at all) from the beginning.
    That's not my goal, big coil and big depths... for that kind of thing I have Pulse Star 2.
    My goal is good sensitivity on the smallest targets and good GEB.
    Of course, the GS4 can also be set to work "slowly" and to work with a coil of 3x3 meters and larger!
    I don't care one bit.
    ​
    Will Pulsar II work as well as GoldScan on highly mineralized soils?

    Leave a comment:


  • Alexismex
    replied
    Hello guys from the forum,
    For those who want to incorporate a microprocessor for the timing in the GS4, it is a big mistake because digital generates a lot of noise .....a lot of noise that you have to clean later, and the detector loses sensitivity, the GS4 circuit is very nice as it says Ivconic, you have to look for refinements and change some parameters but in general it is a wonderful circuit that E.Foster did the design!

    Leave a comment:


  • ivconic
    replied
    Originally posted by ivconic View Post
    The horror!
    I hope that now you have a clearer picture of the situation on the grounds that I visit and about which I have written many times.
    To whom the video is not clear; let me clarify a bit...
    The first program on the video was my custom "deep" program at 7.6kHz.
    In that program, the gold coin is detected at a distance of 24 cm.
    But when I put a brick in front of a gold coin; the range drops to 14-15cm and PLUS Deus reports it as a bad target, very unstable and inaccurate response with many errors, very erratic behavior, etc.
    In the second part of the video, I switched to the Fast2 program, my custom program at 18kHz with silencer at 3 and recovery speed at 2.5
    The range to the gold coin dropped drastically to barely 14cm, and when I put a brick in front, it drops further to about 10cm or less. And it also reports the target as bad, as "trash"...
    So much for that.
    Deus coil is 22.5cm.
    ​
    What I forgot to emphasize here is the following...
    In the video, Deus sees a gold coin through a brick in all possible wrong ways... but still sees that gold coin, even as it's "garbage".
    However, it is a recent gold coin, from 1751. And it's bigger.
    While in real conditions on real terrains, I mostly look for ancient Roman gold coins, which are slightly different in terms of alloy composition (better with more gold).
    Unfortunately, these days I have not been able to find one of these on loan for these tests.
    The problem on the real field is that Deus often does not see such gold coins at all, even as "garbage", it simply remains silent above such targets.
    So what can be seen in the video with Deus... can even be considered a "success" even though it is essentially a horror factual situation.
    So... so much for that. It definitely makes sense to build (or buy) some similar PI and go back to the old sites again.
    ​

    Leave a comment:


  • ivconic
    replied
    Originally posted by Emersonpaz View Post

    I'm going to try to do this project I'm going to opt for post #426 because I don't have a soldering station for SMD lately I don't have much time left for the hobby who knows when I'll complete the project but I'm not in a rush, I always say that but when the boards arrive I can't wait until it's ready . I always thought the GS4 test videos were cool.
    Obey the Alex's schematic when check the pcb, schematic is accurate.
    Same I did.

    Leave a comment:


  • ivconic
    replied

    Leave a comment:


  • Emersonpaz
    replied
    Originally posted by ivconic View Post
    But make no mistake, the previous file has errors, which I didn't know at the time.
    Here is the file with all the mentioned errors.


    ​
    I'm going to try to do this project I'm going to opt for post #426 because I don't have a soldering station for SMD lately I don't have much time left for the hobby who knows when I'll complete the project but I'm not in a rush, I always say that but when the boards arrive I can't wait until it's ready . I always thought the GS4 test videos were cool.

    Leave a comment:

Working...
X