IDX-PRO+VDI

[der_fisherman]

I like your small dimension board but not the expense of mounting holes. It would be nice to have four holes, instead of two. All user interface board are exposed for mechanical stress due push-button or encoder activities.

What I often do (with or without mounting holes in a PCB!) is to put a spot of hot melting glue at each corner and press it onto some part of the inside of the box or similar.

It holds well but the hold can be broken with careful use of a screwdriver or similar if needed......Does not need any metallic hardware like screws, nuts and standoffs, nor do I need to drill holes, which may be a problem anyway with certain sensitive designs....

For me its the perfect answer to the problems of mounting PCBs inside (usually) plastic boxes.

Note, if it doesn't stick, clean with Meths/Denatured alcohol first.

Regards

Andy.

[lutek]

I like your small dimension board but not the expense of mounting holes. It would be nice to have four holes, instead of two. All user interface board are exposed for mechanical stress due push-button or encoder activities.

[Fabian]

Smaller VDI PCB

Hello! Here is the PCB of the VDI in 5x5 cm in case anyone needs it. I do not know if it is very small and if the proximity of the tracks can be a problem. Please DO NOT USE until check that everything is correct, I think so, but I'm only a hobbyist and I can have made a mistake (which I do appreciate you letting me know)
Well, that's all.

regards

¡Hola! Aquí va el PCB del VDI en 5x5 cm en caso de que alguien lo necesite. No sé si es muy pequeño y si la proximidad de las pistas pueda ser un problema. Por favor NO USAR hasta tanto comprobar que todo está correcto, yo creo que sí, pero sólo soy un hobbista y puedo haber cometido algún error (que agradeceré me hagan saber)
Bueno, es todo.

Saludos

[Lefizz]

That looks great. Tell us more

[6666]

Hi

This is my new project:

http://www.youtube.com/watch?v=u6SoCvBTjV4

http://www.lugatek.com/forum/index.php?topic=193.msg1935#new

I will share all documents as soon as possible.

elbombaci
this looks like a very good project, thanks

[Uykusuz]

Hi

This is my new project:

http://www.youtube.com/watch?v=u6SoCvBTjV4

http://www.lugatek.com/forum/index.php?topic=193.msg1935#new

I will share all documents as soon as possible.

[selim]

Hi ivconic
Do you have knowledge of coil winding

[Qiaozhi]

hi holyuser and thank you for everything

i cant find PIC16f88 in my country
please recompile the VDI to PIC16f84

The PIC16F84 does not contain any A2D converters, and therefore cannot be used with the VDI circuit. I cannot believe there are no PIC16F88 ICs in your country. It is a very common device.

[sadeg-f]

hi holyuser and thank you for everything

i cant find PIC16f88 in my country
please recompile the VDI to PIC16f84

[Fabian]

My IDX-PRO PCB´s

Some pictures

[Mullihaka]

It is my IDX-PRO. The circuit layout is the last file I posted and working properly. The penultimate does not work. I have no schematic, I have only Layout.
That is what works.

Hi Eduardo,

For some reason, I can't open this RAR file. Can you check if it is OK? I mean the file with the two tone modification.

Thanks!

[der_fisherman]

LCD Infos and interfacing

Tell me where the first contact?

You can find a lot of extra LCD information here:-

http://web.archive.org/web/20071206202610/http:/www.hippy.freeserve.co.uk/picaxelc.htm#Output_Pin_Definition

although the site is for PICAXE fans first and foremost, it may give more good ideas to anyone seeking LCD infos.

Regards

andy

[Fabian]

Of course..!

Good Job

With your permission I may use it, it will make for cheaper boards

Silverdog

Of course you do! It would be an honor for me, but the credit must be for Eduardo and his excellent work.

Best regards

[silverdog]

Hello people! I adjusted the final circuit made by Eduardo, to make it fit on a 5x5 sheet of fiber, which is the standard that I get in my city. Here I share it, maybe someone needs it.

Regards

Good Job

With your permission I may use it, it will make for cheaper boards

Silverdog

[shansov]

Thank you very much.