Delta Pulse

[Jose]

Jose, in your calculation bundle diameter is 70mm. Is this correct?

Here is calculation with d=0.5mm wire and 7mm bundle diameter. [ATTACH]32013[/ATTACH]

I apologize.
It should be 7mm. Not 70mm.
The inductance for "Bundle diameter" 7 mm, is 1008 uH.
José

[kt315]

making fast basket coil for test

[kt315]

calcoil program I use. needs to install.

http://www.avral.ru/b542b772b87b797e0d1b433c47566f6f

[Hannu]

hi can you put this program here.
regards

http://www.miscel.dk/MiscEl/MiscEl.zip

[mohandes]

Jose, in your calculation bundle diameter is 70mm. Is this correct?

Here is calculation with d=0.5mm wire and 7mm bundle diameter. [ATTACH]32013[/ATTACH]

hi can you put this program here.
regards

[Hannu]

Jose, in your calculation bundle diameter is 70mm. Is this correct?

Here is calculation with d=0.5mm wire and 7mm bundle diameter.

[mohandes]

Calculation for the Miscel program indicates that coil 1x1 mtrs, 16 laps, 580 corresponds uH.
Also you can see that if we use a copper conductor 1.5 mm2 section, the total resistance of the coil is 0.65 ohms, a vajo value for the DP.
So I installed a series resistance of 1 ohm 5W, and it worked better.
Jose[ATTACH]32012[/ATTACH]

hi my dear friend jose
i use cate6 cable and get best result .
i make new coil and put here for share all . i think if have 400mkh to 500 mkh is good and best R between 2.5 to 4 ohm.
about parallel best is 470 ohm to 500 ohm.
best wishes for all .

[Jose]

Calculation for the Miscel program indicates that coil 1x1 mtrs, 16 laps, 580 corresponds uH.
Also you can see that if we use a copper conductor 1.5 mm2 section, the total resistance of the coil is 0.65 ohms, a vajo value for the DP.
So I installed a series resistance of 1 ohm 5W, and it worked better.
Jose

[kt315]

'gold' = very useful info for any dummy =)
something you have to be keeping in touch constantly .

[kt315]

hi.KT315. if 110*110cm coil have 1.2ohm can we add 1ohm 5watt resistor.

i believe dp2 good detector and better than another Pi project. so i want have a new Experience with LCD discrimination .
regards

I see much videos of DP3 in youtube... looks too good. Elbombachi made something the beast... make it and show us a result... =)
yes, you can add 1oHm> resistor in the Source pin of MOS-FET... I did test with it, did not notice something positive...
maybe for low delay PI detectors, especially for gold nugget hunting, PI with 10-15us minimal first strobe delay I mean, it would be really actual...
but for DP thinking would be not.

[Hannu]

gold... we don't have it here. usefull table i see.

Now sled-coil is 500uH. still need to make small round coil with same inductance for indoor testing & damp resistor finding.

[mohandes]

it was working but i'm going to take some turns away. Some schematics are marked "coil 1.1m x 1.1m 16 turns". It makes about 1mH?

hi.KT315. if 110*110cm coil have 1.2ohm can we add 1ohm 5watt resistor.

i believe dp2 good detector and better than another Pi project. so i want have a new Experience with LCD discrimination .
regards

[kt315]

and what? this is a cause to appeal to bulgarians? so they had left the geotech long time away. I give you gold table, keep it for future.

[Hannu]

it was working but i'm going to take some turns away. Some schematics are marked "coil 1.1m x 1.1m 16 turns". It makes about 1mH?

[kt315]

1.7mH would be working but it is not tested. try do mini coil with this L and test it at a table. DP is working with 380-550uH coils.
with 1>mH you ll get more ringing frequency, more amplitude of it, and select the damper resistor value using the o-scope.